manualshive.com logo in svg

Omega BB703, Руководство пользователя, Страница: 7 / 20

Поделиться
Скачать
Omega BB703 Скачать руководство пользователя страница 7

Section 2 - Installation

2.1 Unpacking

Remove the packing list and verify that you have received all your equipment. 

If you have any questions about the shipment, please call our Customer Service 

Department at 
1-800-622-2378 or 203-359-1660. We can also be reached on the Internet at 

www.omega.com 

e-mail: [email protected]
When you receive the shipment, inspect the container and equipment for any 

signs of damage. Note any evidence of rough handling in transit. Immediately 

report any damage to the shipping agent.

The carrier will not honor any damage claims unless all shipping material is 
saved for inspection. After examining and removing contents, save packing 
material and carton in the event reshipment is necessary.

The following items are supplied in the box:
Item: 

    OMEGA 

Part 

Number:

BB703 Blackbody Calibration Source  BB703 or BB703-230
User 

Manual 

   M-3265

Calibration Certificate   

 

CAL-3  (3 DATA POINTS)

Power 

Cord 

   200-0028 

(Domestic), 

 

     200-0107 

(International)

Soft Storage Case 

 

 

IR-0019

2.2 Mounting

Mount the unit on a bench, table top or shelf in a horizontal position and operate 

at least ten inches from any air obstructions to the front panel, rear panel, side 

or top of the unit. Operate the unit in an ambient environment between the 

specified 0 to 40°C (32 to 104°F).

2.3 Ambient Temperature

The target plate of the BB703 can achieve any temperature within the specified 

temperature range of a11 to 400°C (a20 to 752°F) when being 

operated in ambient temperatures up to 25°C (77°F). When operating the unit 

at higher ambient temperatures, the user must not exceed the “Maximum 

Allowable Target Plate Temperature” shown along the y-axis in Figure 2. 

Failure to adhere to these guidelines may cause a safety switch inside the unit 

to open the heater circuit. If the PID light is blinking or continuously on but 

there is no increase in target plate temperature, then the thermal safety switch 

has tripped. In this case refer to Section 3-3.

BB703 Installation

2

2-1

NOTE:

Содержание BB703





















Отзывы:

Нет отзывов