background image

TABLE OF CONTENTS

MODEL 871A AND MODEL 872A

DIGITAL THERMOMETERS

SECTION

PAGE

SECTION 1 INTRODUCTION .................................................................. 1

1.1

General Description ................................................................... 1

1.2

Features ..................................................................................... 1

2.1

Accessory Items......................................................................... 1

SECTION 2 INSTALLATION .................................................................... 2

2.1

Unpacking.................................................................................. 2

2.2

Battery Installation ..................................................................... 2

SECTION 3 OPERATION ......................................................................... 3

3.1

Controls and Indicators.............................................................. 3

3.2

Operating Procedure.................................................................. 5

SECTION 4 SERVICE INFORMATION .................................................... 5

4.1

Verification Check ...................................................................... 5

4.1.1

Functionality Check ................................................................... 5

4.1.2

Accuracy Check......................................................................... 6

4.2

Calibration for Model 871A ........................................................ 6

4.2.1

Equipment Needed .................................................................... 6

4.2.2

Environmental Conditions .......................................................... 6

4.2.3

Setup.......................................................................................... 7

4.2.4

Calibration Procedure ................................................................ 7

4.3

Calibration for Model 872A ........................................................ 8

4.3.1

Equipment Needed .................................................................... 8

4.3.2

Environmental Conditions .......................................................... 8

4.3.3

Setup.......................................................................................... 8

4.3.4

Calibration Procedure ................................................................ 9

4.4

Disassembly for Model 871A and Model 872A.........................10

4.5 Troubleshooting 

Guide .............................................................11

4.5.1

DC Voltage checks Model 871A ...............................................12

4.5.2

DC Voltage Checks Model 872A ..............................................12

4.5.3

Waveform Checks Model 871A ................................................13

4.5.4

Waveform Checks Model 872A ................................................13

SECTION  5

SPECIFICATIONS FOR MODEL 871A
AND MODEL 872A .............................................................13

5.1

Parts List ...................................................................................16

i

Содержание 871A

























Отзывы: