3
aSSeMBLY
(refer to figure 4 on page 4)
1. Thread the connecting block (#12) to middle rod (#6),
then secure to base (#3) with M10 nut and washer
(#21 & 22).
2. Secure top cover (#4) and two holding arms (#14) to
base (#3) with M6x25 bolts, washers & nuts (#15,
16 & 17)
3. Attach wheel axle (#5) to base (#3) with M12x40 bolts
& nuts (#23 & 24)
4. Attach wheels (#18) and washers (#19) to wheel axle
(#5), then secure with cotter pins (#20)
5. Secure the axle links (#5A) of wheel axle (#5) to
connecting block (#12) with M12 bolts and washers
(#13 & 19).
6. Attach hook bracket (#9) to top cover (#4) and secure
with lock pin (#11)
7. Attach angle adjustable wheel (#7) to middle rod (#6)
with set screw (#8).
8. Attach handle (#1) to top cover (#4) with lock pin
(#2).
9. Insert handle grip (#10) to handle (#1).
OPeRatIOn
1. Prepare the brake drum or brake drum/hub assembly
for removal according to the instructions in vehicle
service manual.
2. Place drum handler in a horizontal position.
3. Turn the angle adjustable wheel until the drum han-
dler is in its lowest postion.
4. Position the handler under the drum until the holding
arms meet the outer surface of the drum.
5. Turn the angle adjustable wheel clockwise until the
handler meets the lower surface of the drum.
6. Lower the handle to slightly lift the drum. Pull the
handler and drum back, away from the brake as
-
sembly.
7.
Removing/installing drum only:
Flip the hook bracket into the hub opening of the
drum as shown in figure 2.
Removing/installing drum and hub as assembly:
Position the hook bracket reverse as shown in figure
3 to allow a wheel nut to secure hook to drum/hub
assembly.
8. It may be necessary to adjust the hook. Remove the
hook lock pin, and move the hook bracket to any one
of four hole locations.
9. Pull the drum completely away from the brake as
-
sembly. Slowly and carefully lift the handle to place
the drum face down on the floor, being cautious of
the transfer of load weight.
note
: Reverse the process to Install the brake drum
back to the brake assembly. Be sure to align the drum
with the studs and follow the instructions in the vehicle
service manual.
Hook Position
(for drum only)
Figure 2 - Illustration for removing/installing drum
Brake Drum
Holding Arms
Hook Position
(for drum/hub
assy.)
Drum/Hub Assy.
Figure 3 - Illustration for removing/installing drum/hub
assembly
Holding Arms
•
Study, understand, and follow
all printed mate-
rials provided with and on this device
before
use.
• Ensure that vehicle is chocked, lifted, and sup
-
ported by adequately rated jack stands
before
using this product!
• Use only for removal, installation, and transport
of brake drum/hub assys which nest and can be
secured within the bed frame and holding arms.
•
dO nOt
overload. Bending, bowing, or cracked
components are visible evidence of overloading.
If such deformation is noted,
STOP
, immediately
discontinue use and transfer load to a drum han
-
dler of greater capacity.
•
Secure
drum
before
transporting.
• Use only on hard, level surface.
• Raise and lower the brake drum slowly.
• Always wear steel-toed shoes when using this
device.
• Brake drum dust is hazardous to your health.
Consult Federal, State and local regulations con
-
cerning the safe handling of asbestos and what
precautions to take when handling.
• Failure to heed these markings may result in
personal injury and/or property damage.
WARNING
!