background image

2

PRePARATIOn

Assembly 

(see Replacement Parts page 6 for reference to parts location & assembly sequence)  

Assemble, align and insert the handle assembly & handle position bar into the handle sleeve, then tighten the bolt 

on handle sleeve to prevent accidental removal of handle while in use.

Before Use

1. 

Verify that the product and application are compatible, if in doubt call Omega Technical Service  (888) 332-6419.

2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the 

product, its components and recognize the hazards associated with its use.

3. To familiarize yourself with basic operation, locate and turn the release valve (handle knob):

  a. Clockwise

 until firm resistance is felt to further turning. This is the ‘

CLOSed

’ release valve position used to 

      

raise

 the load.

  b. Counter-clockwise

, but no more than 1 full turn from the closed position. This is the ‘

OPen

’ release valve 

      position used to 

lower

 the load. The more you turn the release valve counter-clockwise, the faster the load 

      descends.

4. With ram fully lowered, remove the oil filler plug. Check oil level. Proper oil level should be just below the rim of 

the opening. Reinstall the oil filler plug.

5. Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve. Connect to air 

supply, then squeeze the lift control valve for 3 seconds to evenly distribute lubricant.

 

note:

 These models are equipped with the popular 1/4" NPT air coupler. When installing a different air coupler of 

your choice, ensure that thread tape or compound is used when servicing connections. To ensure dependable, 

trouble free operation an inline air dryer and oiler is recommended.

6. Ensure that jack rolls freely. Raise and lower the unloaded ram throughout the lifting range before putting into 

service to ensure the jack operates smoothly. Replace worn or damaged parts and assemblies with Omega 

authorized replacement parts only.

Bleeding / venting Trapped Air

With the release valve in the OPEN position (3b.) and with ram fully lowered, locate and remove the oil filler plug.  

This will help release any pressurized air which may be trapped within the reservoir. Reinstall the oil filler plug.

SAFeTY and GeneRAL InFORMATIOn

Save these instructions. 

For your safety, read, understand, and follow the information provided with and on this jack 

before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating 

procedures before attempting to use. The owner and operator shall be aware that use and repair of this product 

may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's 

native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack, 

remove from service immediately. 

Inspect before each use.

 Do not use if broken, bent, cracked or damaged parts are noted. Any jack that appears 

damaged in any way, or operates abnormally shall be removed from service immediately. If the jack has been or 

suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately 

discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer 

for list of authorized service centers). It is recommended that an annual inspection be done by qualified personnel. 

Labels and Operator's Manuals are available from manufacturer.

 

!

PROdUCT deSCRIPTIOn

This category of Hydraulic Truck Jack is designed to lift, but not support, rated capacity partial vehicle loads consisting 

of one end of a vehicle. 

Immediately

 after lifting, loads must be supported by a pair of appropriately rated jack 

stands.

NEVER

 use a hydraulic jack as a stand-alone device. After lifting, 

immediately

 support the lifted vehicle with 

a pair of appropriately rated jack stands. 

NEVER 

place 

any 

portion of your body beneath the vehicle when

lifting 

OR

 lowering!

Содержание 23301C









Отзывы: