background image

Important Information — Please Read Before Use

MOBILE WORKSTATION WM-DP1

2

Important Information — Please Read Before Use

Intended use

The Olympus WM-DP1 mobile workstation is intended for use in medical facilities 
under the direction of a trained physician, and has been designed to be used with 
a range of Olympus equipment to facilitate GI endoscopy, endoscopic 
ultrasound, respiratory and surgical endoscopic procedures. Do not use the 
equipment for any purpose other than its intended application.

The safety and performance of an endoscopic system depends not only on the 
endoscope but also on the ancillary equipment used with it. Ensure any ancillary 
equipment is compatible with the endoscope and other equipment used. 

Instruction manual

Please read this manual carefully before attempting to use the Olympus 
WM-DP1 mobile workstation as it contains important information on the proper 
care, handling and use of the equipment. In addition, read the manuals of any 
other units (light source, endoscope, etc.) that form part of the system.

If you have any questions or comments regarding the information in this manual, 
please contact Olympus. These instructions should be retained for reference 
during the life of the product.

Signal words

The following signal words are used throughout this manual:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could 
result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may 
result in minor or moderate injury. It may also be used to alert against 
unsafe practices or potential equipment damage.

NOTE

Indicates additional helpful information.

Содержание WM-DP1





































Отзывы: