Olympus OmniScan MX Скачать руководство пользователя страница 43

Страница: 43 / 230

DMTA-20015-01EN [U8778402], Rev. M, February 2017

Overview of the Equipment

1.3

Left Side Panel

The left side panel of the OmniScan MX2 (see Figure 1-3 on page 31) contains
standard computer interface ports used for expanded connectivity.

Figure 1-3 Left side panel of the OmniScan MX2

USB ports (3)

The USB ports (see Figure 1-3 on page 31) accommodate USB peripherals such as
external keyboards, mice, storage devices, or printers.

Ethernet (RJ-45) port

Used to connect to an Ethernet network.

Serial port

Used mainly for debugging, or to supply DC power to accessories.

OTG (On-the-Go USB port,
compatible with USB 2.0)

PA connector

Ethernet (RJ-45) port

Serial port

High-speed (HS) USB port
(compatible with USB 2.0)

Full-speed (FS) USB port
(compatible with USB 1.1)

UT connectors

Содержание OmniScan MX







































































































































































































































Результаты поиска

Содержание OmniScan MX

Отзывы:

Похожие инструкции для OmniScan MX

Бренды по названию

Популярные бренды

Olympus OmniScan MX, Руководство пользователя

Результаты поиска

Содержание OmniScan MX

Отзывы:

Похожие инструкции для OmniScan MX

Бренды по названию

Популярные бренды