Olympus HydroForce M500H Скачать руководство пользователя страница 3

Страница: 3 / 45

Introduction

Congratulations on your purchase of the Hydro-Force Olympus M500H. The

M500H is designed to give truckmount-level performance in a portable machine

that combines versatility with ease of transport. Years of experience, engineering,

and planning have gone into the design and manufacturing of the M500H. We

take a great deal of pride in the M500H; our goal is no less than your complete

satisfaction.

This manual will provide users with the knowledge required to operate the

Olympus M500H safely, to understand how to properly operate and maintain the

machine, and to ensure that the equipment operates at its maximum performance

level.

All users must read and understand this manual completely before

operating the machine.

Always maintain this manual in legible condition adjacent to the Olympus

M500H, or place in a secure location for future reference.

Any questions pertaining to the operating or servicing of this unit should be

directed to your nearest Hydro-Force distributor.

This manual is written specifically for the Olympus M500H portable extractor

units manufactured by:

Hydro-Force

542 W Confluence Ave.

Salt Lake City, UT 84123

801-268-2673

801-268-3856 FAX

Information in this manual is subject to change without notice and does not

represent a commitment on the part of Hydro-Force or its parent or affiliated

companies.

Содержание HydroForce M500H














































Результаты поиска

Содержание HydroForce M500H

Отзывы:

Похожие инструкции для HydroForce M500H

Бренды по названию

Популярные бренды

Olympus HydroForce M500H, Руководство по эксплуатации

Результаты поиска

Содержание HydroForce M500H

Отзывы:

Похожие инструкции для HydroForce M500H

Бренды по названию

Популярные бренды