2
6.
Scan the QR code displayed in the
Tuya Smart
app from a
distance of 15 to 20 cm using the camera
8
in the doorbell
14
.
7.
Use the
Tuya Smart
app to confirm that you heard an acoustic
signal from the doorbell
14
after the scanning process.
►
A counter runs backwards until the connection has been
established.
►
When a connection has been established, you hear an
audible confirmation from the loudspeaker
7
in the
doorbell
14
.
Assembling the Doorbell
Before beginning assembly, check that camera surveil-
lance is permitted in the area concerned. Also check
whether the area being monitored must be identified.
When using the wireless option, pay attention that the
installation location of the camera
8
is within the operat-
ing range of the home network (wifi system).
Insert the microSD memory card before completing the
wall installation.
Selecting an Installation Location
The doorbell
14
is splashproof at the installation location in accord-
ance with the criteria defined for Protection Class IP44. When
assembling the doorbell
14
, pay attention that it is installed in a dry
location and the electrical equipment will not get wet. Ideally, the
doorbell
14
should be installed at a height of approx.1.5 metres.
Install the doorbell
14
directly beside the entrance door and use the
bell wire (AC 8 – 24 V) provided for the power supply.
Alternatively, you can recharge the battery in the doorbell
14
at regular intervals by connecting the USB cable
supplied or a powerbank (not contained in the package
supplied) to the USB charging port
12
.
Warning!
Risk of fatal injury from electric shock or
gas explosion! During installation, pay attention to the
possibility of electrical cables and gas pipes running
in the walls. Pay attention that you do not damage
electric cables or gas pipes. In case of doubt, contact
a specialist!
Attention!
Before starting any assembly work,
unscrew any relevant fuses.
Call in a trained electrician to complete the connection.
1.
Ensure that the power supply to the bell wire has been discon
-
nected.
2.
Ensure that there are no electric cables, gas or water pipes near
the installation location.
The mounting plate must be assembled on the wall first. Pay
attention that the mounting plate is correctly aligned. The
opening for the feed-through of the bell wire must point down-
wards.
3.
Mark the drill holes at the distance measured on the wall at the
installation location.
4.
Drill the holes.
5.
Insert the appropriate dowels contained in the assembly material
supplied.
We recommend the use of special dowels according to the
properties of the mounting surface.
6.
Fix the mounting plate on the wall using the screws supplied.
7.
Two bell wires come out of the wall. Connect each bell wire with
a bell wire in the doorbell. Use the clamping devices
16
for this
(contained in the package supplied). You need not pay attention
to the polarity of the bell wires.
8.
Tighten the clamping devices
16
by turning them clockwise.
9.
Ensure that the doorbell
14
is switched on via the
On/Off switch
10
.
10.
Fix the doorbell
14
to the mounting plate using the screws
supplied.
11.
Switch on the power supply to the bell wire.
► The light ring around the bell button flashes red.
Circuit Diagram 1: Connecting to the building wiring
AC
8 V - 24 V
13
14
15
13
Current source
(AC: 8 V - 24 V)
15
House doorbell
14
Doorbell
Circuit Diagram 2: Extension with door opener
Lock
2
AC
8 V -
24 V
Lock
1
AC
8 V -
24 V
20
17
16
19
18
AC 8 V - 24 V
The doorbell
14
has 2 connections for the door lock
20
. In the circuit
diagram, Connection 2 is indicated. The designation also applies for
Connection 1.
16
Terminal
19
Current source
(AC: 8 V - 24 V)
17
Bell wire socket
20
Door lock
18
Door lock 2 socket
Installing the CA 824 Function Board
If hissing or humming noises can be heard after the doorbell
14
has
been properly installed, you can install a CA 824 function board in
the bell to clear the noises.
More information is available in the
Installing the CA 824 Function
Board
information sheet enclosed.
Operating the Doorbell
The following illustrations do not reflect the quality of the images
provided by the
Tuya Smart
app. They are made unrecognisable
due to reasons of personal rights.
1.
Press the
Bell button
6
.
►
A video call is started in the
Tuya Smart
app.
2.
Press the
Call button
in the
Tuya Smart
app.
►
The call begins.
You can control two door locks (Door Lock 1 / Door Lock 2)
20
via
the
Tuya Smart
app. Actuation of a door lock
20
is described below.
The door lock
20
must be connected to the doorbell
14
in
order to use the
Tuya Smart
app to operate the door
lock
20
.
3.
Use your finger to draw the button upwards.
4.
Press on the lock icon.
►
You have unlocked the door.
5.
End the call by pressing on the
On-hook button
.
►
The call is ended.
