1
1
1
2
Luminaire
Mounting accessories
Manual
Pictograms
1
2
3
Surface mounting on a Wall with A-1134 base (Included in the package)
Single sided luminaire
o
These devices are used indoors
(
ta 40 C
)
in
places where emergency light is needed.
Each device must be permanently
connected to mains power supply
.
In
normal operation the battery is charging. In
case of a mains power supply failure, the
device enters emergency mode and the
illumination LED turns on. When the mains
power supply is restored the device turns
to normal operation.
If the luminaire is not connected to the
panel, the following automatic tests
executed:
Manual
Operational
Test
The illumination source and the autonomy
tests are programed by the control panel.
The tests results are send to the control
panel.
Automatic Operational Test
The Automatic Autonomy Test is conducted
every 6 months and measures the device’s
back up operation and emergency duration.
In order to be performed, the mains power
supply and the battery should be connected
and fully charged
.
If the battery is not fully
charged
,
the test is postponed
until the
battery is completely charged. If during this
test, the autonomy is less than nominal
then the battery fault led turned on
continuously and the battery must be
replaced.
T
his test includes all the operations that are
provided in manual operational test and is
conducted automatically every 15 days and
lasts 3 seconds.
By pressing the test button an operation
test is initiated. The light source and the
emergency circuit of the device are tested.
The manual test can be conducted only if
the mains power supply and the battery are
connected. During this test period all
indications LED are OFF.
Automatic Autonomy Test
Tests
3. The device must be connected to the
mains power supply through a circuit
breaker that is depends on the total
line’s power load.
2. Always use in any case round mains
cable
,
with a diameter
of 5
-
10mm
(H05RN-F type 2x1mm²
or
any
other
type
,
at least
equal
to it’s mechanical
and electrical properties). ATTENTION!!
The cable must not be deformed in any
way (This requirement is important to
ensure the
ΙΡ
rating).
Resetting Errors
ΑΤΤΕΝΤΙΟΝ!
!!
4. In case of battery replacement, it must
be replaced by the same type, by the
manufacturer or a competent person.
Press and hold the TEST button for more
than 5 seconds. The luminaire will erase
first the errors (3 LED indicators will light in
succession) and after 2 seconds the LED
Lamp Fault will remain lit steadily. When
the TEST button is released, the luminaire
will change between maintained or non -
maintained mode. The change is recorded
permanently in it’s memory.
Changing The Operating Mode
The luminaires can be connected to the
addressable panels of Olympia Electronics.
For address operations refer to the
installation manual of the panel. For
address connections see page 2.
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only
.
Push the Test button for more than 5
seconds, to delete all the indicated LED
errors. Then the device enters regular
operation mode.
Addressable Communication
6.
It is not allowed to discard batteries
into common trash bins, they must be
discarded only in battery recycling
points. Do not incinerate.
5. In case of inactive use for a period
greater than 2 months, disconnect the
battery by pulling out the battery’s
connector.
Οptional Mounting Methods (Upon Request)
General
Package Contents
922502862_09_009
922502862_09_009
922502862_09_009
Description
Indications
LED Status
BATT.
FAULT
(
red
)
LAMP
FAULT
(
red
)
CHARGE
(
green
)
Charging
Lamp Fault
Battery fault
No charging current or disconnected battery
Permanently ON
Blink
Indifferent
Off
1
1
1
1
1
1
1
1
1
1
1
2
3
5
3
4
4
2
Installation Instructions
A
A
A
A
B
Signal Cable
Power Cable
N
L
+L
-L
-L
N
N
L
L
-L
L
L
Power Connection
Communication Connection
From
Panel
A
A
B
B
LOCK
B
B
LOCK
Make the connections
Follow step 4 of installation on page 2
Α-1130
Α-1131
Α-1132
Tube
Α=1
m
Α=0
.
5
m
Α=0
.
25
m
Flag mounting
A-1133 SET
(only for
ZLD-28/EM/ADR, ZLD-34/EM/ADR)
Hanging mounting
A-1130, A-1131, A-1132 SET
CHANGE ADDRESS POINT
CHOOSE FROM 1 TO 250
ENTER TO CHANGE
- - -
006
NEW
OLD
Programming the address of a luminaire
3) You must go to the menu:
4) Set the new address using the UP and DOWN keys and press enter when done.
TECHNICIAN MENU => SETTINGS=> CHANGE ADDRESS POINT
1) The luminaire must not be connected with the mains power supply not with the battery.
2) One end of the cable is connented to the luminaire and the other end to the panel.
To program or change the address of a luminaire you must connect the luminaire to the panel
alone and do the following steps:
