Thank you for purchasing this product of
Olympia Electronics. A European manufacturer.
DESCRIPTION
The BS-464 (figure1
)
is a module that can be
fitted only on the main board of the BS-468
b u r g l a r
a l a r m
p a n e l
f r o m
O l y m p i a
Electronics. It can receive and send SMS
messages to and from selected telephone
numbers.
These telephone numbers are
stored in the BS-468 panel’s memory and do
not erase in the event of a power failure but
can be changed by the user for as many
times as required
.
The BS-464 can also
accept commands from unknown telephone
numbers if the user requires.
INSTALLATION
The user must install the antenna
(figure
4)
and the SIM card(figures
2 & 3)
on the board
for it to become operational.
Next, the card
is installed on the BS-468 panel
(figure
5)
.
GENERAL INSTRUCTIONS
Verify that the GSM unit is placed in an area
were the signal is adequate. This can be
checked via the BS-466 keyboard. The scale
shows 0 to 4 bars. Signals lower that 2 bars
can cause bad sound quality and calls that
cannot be sent and received. In this case it is
advised to test the system using a SIM card
from another provider. Please note that if a
call is not feasible due to a low signal, when
the signal is obtained the GSM will send a
verbal message containing the alarm status
during the time of the unfeasible call. This is
valid only if this service is activated by the
provider.
If the GSM unit is installed near a boarder
line then there might be increased charges
due to the roaming service. To avoid this,
deactivate the roaming service.
S o m e t e l e p h o n e u n i t s m i g h t e x h i b i t
sensitivity due to being near the GSM unit. If
something like this is observed it is advised
t o r e o r i e n t o r t o r e l o c a t e t h e a ff e c t e d
telephone device.
Each and every remote command to the GSM
u n i t m u s t b e a c c o m p a n i e d w i t h a v a l i d
access code.
Warning!!
It is not advised to use a high gain
or directional antenna in order to improve the
signal strength. Using such antennas will
lead to unstable communications because
only one cellular base will be used by the
GSM unit. Be advised that GSM systems do
not operate correctly when the cellular base
station is more that 30km away because of
communication delays. This is true even if
the signal is strong.
Warning!!
The use of pre-paid SIM cards in
the GSM unit is not advised because some
providers block these card when they do not
have enough credit or when they are not get
credited often. If this is the case with your
provider then use tariffed SIM cards.
SIM CARD
It is suggested to install a SIM card, on the
BS-464, that will not require a PIN number
during the startup of the device
. To disable
the PIN requirement, insert the SIM card into
a c e l l p h o n e a n d d i s a b l e t h e P I N
requirement. Next remove the SIM card from
the cell phone and insert it into the SIM card
holder of the BS-464.
WARNING
:
Never insert or remove a SIM
card from the BS-464 when the BS-464 is
powered. There is a chance that the SIM
card might be damaged. To insert/remove
the SIM card we must either remove the
GSM module from the panel or we can
leave it on the panel and disconnect the
panel’s power supply and battery.
TECHNICAL CHARACTERISTICS
Ο
P
ΕΡΑΤΙΟΝ
TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
WEIGHT
GUARANTEE
OPERATION VOLTAGE
CONSUMPTION
Powered by the BS-468 panel
0 to 60 C
o
Up to 95%
2
years
4
5gr.
101
x
61
x
2
5 mm
92
1464
000_09_0
0
6
Page
1 from
4
BS-464
GSM TELEPHONE DIALER CARD FOR BS-468 PANELS
30mA (
quiescent)
. 120mA (
during a call)
PRODUCED IN ACCORDANCE WITH
EN
50130-4, EN
55022, ETSI EN 301 489-7, ETSI EN 301 511, EN 60950-1, ETSI EN 301 419-1
High Quality European based Manufacturers