OLT SSGS812-FJ-Ply Скачать руководство пользователя | Manualshive

Страница: 9 / 38

background image

Note:

The floor will be flipped over and floor runners will sit

on your foundation. It is important to note that having a
level foundation is critical. Choosing a foundation will vary
between regions. Typical foundations can be concrete
pads or patio stones positioned underneath the floor
runners.

10.

With Floor Runners attached, carefully flip the

floor over and place on your foundation.

Caution:

you

will need 2 people to assist you. Be careful when
laying floor down not to bend or twist floor. When in
place, level floor completely.

Foundations

9.

Complete all Floor Runners.

11.

Position

Plywood Floor

pieces

(6) on top of completed Floor Joists. The Plywood is cut

slightly smaller than floor framing and will sit slightly back from outside edge. Keep plywood seams
tight.

Hint:

Use a chalk

line to mark location
of floor joists to
determine screw
placement.

Front

12.

With Plywood positioned correctly on

floor framing, attach with 1 1/4” screws. Use
screws every 16”.

plywood

pushed together

at seams.

Concrete Slab
Foundation

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 9

«
...
7
8
9
10
11
...
»

Содержание SSGS812-FJ-Ply







































Отзывы:

Нет отзывов

Похожие инструкции для SSGS812-FJ-Ply

Polytunnel Greenhouse 3x8m

Бренд: Dancover Страницы: 7

Бренд: Dancover Страницы: 30

Бренд: Palram Страницы: 16

Lean To Grow House 4x2

Бренд: Palram Страницы: 64

Бренд: ACD Страницы: 57

Бренд: ACD Страницы: 62

Бренд: ClearSpan Страницы: 19

04GREEN0406SD-V6

Бренд: Mercia Garden Products Страницы: 12

Бренд: Rowlinson Garden Products Страницы: 24

Бренд: Rowlinson Garden Products Страницы: 25

Junior Victorian

Бренд: Exaco Страницы: 29

EOS JUNIOR VICTORIAN

Бренд: Exaco Страницы: 40

Бренд: Exaco Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды