background image

43.

 Attach 

4A - Bottom Skirting

 around the base of the shed. 

Skirting will hide floor framing. Start with side skirting pieces 
first and attach with 

4 - 1 1/2” Finishing Nails 

per piece.

4. Trim & Miscellaneous Section

Exploded view of all parts necessary to complete the Skirting, Trim, Facia and Miscellaneous 
Pieces. Identify all parts prior to starting.

Parts (Steps 43 - 44) 

4A - Side/Rear Bottom Skirting - Bevel 

(1/2” x 4 1/2” x 45 1/4”) 

x 5 

Hardware (Steps 43 - 44)

 

N1 - 1 1/2” Finishing Nails

 x 20 total

Side Facia 
(Part 4Q)

Side Rear 
Corner Trim 
(Part 4P)

Rear 
Corner Trim 
(Part 4O)

Rear Corner 
Filler Trim 
(Part 4D)

Front Corner 
Filler Trim 
(Part 4C)

Side/Rear 
Bottom Skirting 
(Part 4A)

Sliding Doors 
(Part 4F)

Window 
Inserts 
(Part 4V)

Window 
Trim  
(Part 4W)

Interior Door 
Flange (Part 4G)

Sliding Door Track 
Stop (Part 4J)

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 27

Note: All Trim, Facia, and Bottom Skirting pieces will be positioned rough face out when installed.

Side Front 
Corner Trim 
(Part 4N)

Front Corner 
Trim (Part 4M)

Lower Door Track 
Cover (Parts 4I)

Lower Door 
Track (Part 4H)

Front Bottom 
Skirting (Part 4B)

Rear Facia - L/R 
(Part 4R)

Front Facia - L/R 
(Part 4R)

Front Facia 
(Part 4S)

Facia Detail 
Plates (Part 4T)

Metal Drip Caps 
(Part 4U)

Содержание SpaceSaver SS124-SLIDER-METAL-FJ








































Отзывы: