manualshive.com logo in svg

OLT SM812-FJ-Ply, Инструкция по сборке, Страница: 39 / 43

Поделиться
Скачать
OLT SM812-FJ-Ply Скачать руководство пользователя страница 39

Inside Edge of 
Door Frame

Drill 1/2” Diameter Hole to 
accommodate rod of Cane Bolt.

71.

  Position and attach 

Vertical Door Flange 

on 

inside edge of door frame 

(left door from outside) 

using 

6 - 2” Screws

.

Parts 

Interior Door Flange 

(1/2” x 2 1/2” x 71”) 

x 1

Hardware 

S3

 

- 2” Screws

 

x 6 total

72.

 The Interior 

Cane Bolt

 will be attached to Vertical Door Flange. To 

position Cane Bolt correctly, attach to flange first, close doors and mark 
hole to house Cane Bolt Rod. Open doors and drill hole where previously 
marked with 1/2” bit. Attach Cane Bolt with 3/4”black screws.

Hardware 

Y6

 

- Cane Bolt

 x 1 total 

SB1

 

- 3/4” Black Screws

 

x 6 total

73.

 Attach 

Door Handles 

and Exterior Black 

Barrel Bolt

 to door.  Attach Barrel 

Bolt as illustrated above with 

5 - 2” Black Screws 

&

 1 - 3/4” Black Screw

.  Note 

how female part of Barrel Bolt is positioned higher than male.  Do a dry run first 
to position Barrel Bolt correctly.  Attach each Door Handle with 

4 - 3/4” Black 

Screws

, ensure screws connect with inner door stud. 

Important: 

 Drill pilot holes with 1/8” drill bit prior to securing with screws to pre-

vent wood splitting.

Hardware 

Y3 - Door Handles

 x 2 total 

Y4 - Barrel Bolt

 x 1 total 

SB1

 

- 3/4” Black Screws

 

x 9 total 

SB2

 

- 2” Black Screws

 

x 5 total

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 39

Содержание SM812-FJ-Ply












































Отзывы:

Нет отзывов