OLT GS63-TG-CEDAR Скачать руководство пользователя

Страница: 25 / 29

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 25

45.

Starting with Right Door first, lift and position Door in opening. Leave a 1/8” gap on right side

and 1/8” gap on the bottom. Use a

Cedar Shingle Shim

to shim the Door at bottom to help position

door evenly. When Door is aligned correctly, screw Hinge into Vertical Door Frame Trim with

1 - 2”

Black Headed Screws.

Use only 1 screw initially per Hinge until both Door alignments are

confirmed. Drill pilot holes to prevent wood from splitting.

1/8”
gap

1 - 2” Screw per
Hinge Initially.

46.

Position Left Side Door (with Flange) as per

Step 45

. Once again, use only

1 - 2” Black

Headed Screw

per Hinge initially to secure door to Vertical Door Frame Trim.

Left Side Door.

47.

With both Doors partially attached, check to

see Doors open and close correctly. Make any
necessary adjustments and when satisfied,
completely secure Hinges to Vertical Door Frame
Trim with

two

2” Black Headed Screws

per Hinge. Drill pilot holes to prevent wood from
splitting.

2 more - 2” Black Headed
Screws per Hinge

48.

Attach

Door Handles

to Doors with

4 - 3/4” Black Headed Screws

per Handle.

Choose desired Handle height.

Hardware

Black Handle

x 2 total

3/4” Black Headed Screws

x 8 total

Содержание GS63-TG-CEDAR






























Результаты поиска

Содержание GS63-TG-CEDAR

Отзывы:

Похожие инструкции для GS63-TG-CEDAR

Бренды по названию

Популярные бренды

OLT GS63-TG-CEDAR, Инструкция по сборке

Результаты поиска

Содержание GS63-TG-CEDAR

Отзывы:

Похожие инструкции для GS63-TG-CEDAR

Бренды по названию

Популярные бренды