OLT 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding Скачать руководство пользователя

Страница: 37 / 42

64.

Next, position and secure the Double Doors. Starting with

Right Side Door

, position so there

is a 1/2” gap on bottom and approximately 3/8” on the side. Use a spare Shingle to shim door in place
at the bottom. Secure hinges to Door Trim with

3 - 2” Black Screws

per hinge.

Hint:

Do not attach

all the 2” screws until both doors are positioned correctly into place. Use Screw Driver to tighten
screws completely.

65.

Position

Left Side Door

as per

Step 64

and secure with 2” Black Screws. When satisfied with

door positioning, complete all 2” Black Screw attachments.

Note:

Do not over tighten hinge screws

when using screw gun. Tighten 3/4 of the way and use a Screw Driver to finish so as not to strip
screws.

66.

Attach

Horizontal

and

Vertical Door Stops

Door Header and Jambs. Start with Horizontal Stop first
and then complete both Vertical Stops. Position so door
gap is covered. Use

4 - 2” Screws

per piece to secure.

Parts (Step 66)

Horizontal Door Stop

(1/2” x 2 1/2” x 68”)

x 1

Vertical Door Stops

(1/2” x 2 1/2” x 72”)

x 2

Hardware (Step 66)

- 2” Screws

x 12 total

3/8” gap on side,
1/2” gap at bottom.

Front Bottom Skirting

Bottom of Door

2” Black Screws

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 37

Содержание 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding











































Результаты поиска

Содержание 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding

Отзывы:

Похожие инструкции для 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding

Бренды по названию

Популярные бренды

OLT 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding, Инструкция по сборке

Результаты поиска

Содержание 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding

Отзывы:

Похожие инструкции для 12x12 Space Maker Garden Shed with Plywood Roof & AK Siding

Бренды по названию

Популярные бренды