Olmo Premion Series Скачать руководство пользователя страница 48

The following cases may not always be a malfunction, please check it before asking for service.

20

Troubleshooting

Trouble

Analysis

Does not run

No cooling or 

heating air

Ineffective control

Does not operate 

immediately

Peculiar odor

A sound of 

flowing water

Cracking sound is 

heard

Spray mist from

 the outlet

The running indicator flashes on constantly,

and indoor fan stops.

For the reason that all indoor units use one outdoor 

unit, outdoor unit can only run with same mode

(cooling or heating),so,when the mode you set is 

different from the mode that outdoor is running with, 

mode interfere occurs. Following shows the mode

interfere scene.

The unit is shifting from heating mode to defrost.

The indicator will flash within twelve minutes and

 returns to heating mode.

Is the air filter dirty?

Are the intakes and outlets of the air 

conditioner blocked

Is the temperature set properly

don't run

If the protector trip or fuse is blown.

 If the plug is not properly plugged.

If batteries in the remote controller exhausted.

Please wait for 3 minutes and start again, 

protector device may be preventing unit to work.

.

If strong interference(from excessive static 

electricity discharge, power supply voltage 

abnormality)presents, operation will be 

abnormal. At this  time, disconnect from the 

power supply and connect back 2-3 seconds later.

Changing mode during operation, 3 minutes 

will delay.

This odor may come from another source 

such as furniture, cigarette etc, which is

sucked in the unit and blows out with the air.

Caused by the flow of refrigerant  in the 

air conditioner, not a trouble.

Defrosting sound in heating mode.

The sound may be generated by the expansion 

or contraction of the front panel due to change

of temperature.

Mist appears when the room air becomes 

very cold because of cool air discharged 

from indoor unit during 

COOLING 

or 

DRY

operation mode.

Mode interfere

outdoor unit always run with the mode of first indoor unit that turned on. 

when the setting mode of following indoor unit is interfered with it, 3 beeps 

would be heard, and the indoor unit interfered with the normal running units

would turn off  automatically.  

mode interfere

cooling

cooling

dry

dry

heating

heating

fan

fan

normal

Содержание Premion Series


























































Отзывы: