Olivetti d-Copia 283MF plus Скачать руководство пользователя страница 162

Страница: 162 / 187

Troubleshooting

8-6

OPERATION GUIDE

Troubleshooting

When a problem occurs, first check the following. If the problem persists, contact your dealer or service
representative.

Symptom

Checkpoint

Corrective Action

Reference

Page

Cannot send document.

Is the modular cord
connected correctly?

Connect the modular cord
correctly.

–

Communication error

displayed?

Remedy the cause of error
and send again.

Appendix-13

Is TX (transmission)
restriction activated?

Cancel the TX restriction.

6-15

Cannot perform broadcast
transmission.

Is free space available in the
memory?

Send after the memory has
free space, or create free
space in the memory.

4-4

Cannot perform encrypted
communication.

Are the registrations correct
both at sender and recipient?

Double-check the
registrations both at sender
and recipient.

6-25

Cannot use the remote
switching function.

Is a pulse line used?

Some phones may transmit
tone signals using buttons.
Refer to the operation
manual of your phone set.

–

Is the remote switching
number correct?

Check the registration.
(Default: 55)

4-12

No print output after
reception.

s memory forwarding

activated?

Check the forwarding
destination.

–

Cannot receive document.

Is the modular cord
connected correctly?

Connect the modular cord
correctly.

–

Communication error

displayed?

Remedy the cause of error
and ask the sender to retry.

Appendix-13

Is RX (reception) restriction
activated?

Cancel the RX restriction.

6-23

Cannot perform memory
reception.

Is free space available in the
memory?

Receive after the memory
has free space, or create free
space in the memory.

3-10

Содержание d-Copia 283MF plus




























































































































































































Результаты поиска

Содержание d-Copia 283MF plus

Отзывы:

Похожие инструкции для d-Copia 283MF plus

Бренды по названию

Популярные бренды

Olivetti d-Copia 283MF plus, Руководство по эксплуатации

Результаты поиска

Содержание d-Copia 283MF plus

Отзывы:

Похожие инструкции для d-Copia 283MF plus

Бренды по названию

Популярные бренды