Olivetti d-Copia 283MF plus Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 187

Olivetti d-Copia 283MF plus Скачать руководство пользователя страница 139

Setup and Registration

OPERATION GUIDE

6-23

6

Setting Send Restriction

You can restrict the other parties to which you send originals only to the ones registered in Permit FAX No. and
Permit ID No. as well as the ones registered in the Address Book. To change the sending restriction, follow the
steps below.

1

Press the

System Menu/Counter

key.

2

Press the

U

or

V

key to select [FAX].

3

Press the

OK

key.

4

Press the

U

or

V

key to select [TX/RX Restrict.].

5

Press the

OK

key.

6

Press the

U

or

V

key to select [TX Restriction].

7

Press the

OK

key.

8

Press the

U

or

V

key to select sending restriction.

To not use the sending restriction, select [Off]. To
restrict the other parties only to the ones registered
in Permit FAX No. and Permit ID No. as well as the
ones registered in the Address Book, select
[Addr Book].

9

Press the

OK

key.

Setting Reception Restriction

You can restrict incoming faxes so that you only receive originals from senders registered in Permit FAX No. and
Permit ID No. and senders registered in your Address Book. This mode also allows you to set a [Reject List] for
Reception Restriction so that reception from senders on the list of Rejected FAX numbers or from senders
whose Local FAX Number is not registered are rejected. To change the reception restriction, follow the steps
below.

1

Press the

System Menu/Counter

key.

2

Press the

U

or

V

key to select [FAX].

3

Press the

OK

key.

4

Press the

U

or

V

key to select [TX/RX Restrict.].

5

Press the

OK

key.

6

Press the

U

or

V

key to select [RX Restriction].

7

Press the

OK

key.

«
...
137
138
139
140
141
...
»

Содержание d-Copia 283MF plus




























































































































































































Отзывы:

Нет отзывов