Olivetti d-Color MF25 Скачать руководство пользователя страница 416 | Manualshive

Страница: 416 / 587

background image

9

Replacing toner cartridges and staples and emptying waste containers

9-6

d-Color MF25

7

CAUTION

Precautions for toner spills

%

Be careful not to spill toner inside the machine or get toner on your
clothes or hands.

%

If your hands become soiled with toner, immediately wash them with
soap and water.

%

If toner gets in your eyes, immediately flush them with water, and then
seek professional medical attention.

2

Reminder

Do not replace the toner cartridge until the message “There is no Toner.”
appears. In addition, do not replace the toner cartridge of any color other
than the one indicated in the message on the touch panel.

To replace the toner cartridge

The procedure for replacing any of the toner cartridges (yellow (Y), magenta
(M), cyan (C) or black (K)) is the same.

Example: Replacing the black toner cartridge

0

When replacing the black toner cartridge, be sure to replace filter 2. A
new filter 2 is included in the package with the black toner cartridge.

0

When replacing the black toner car-
tridge, be sure to clean the electrostat-
ic charger wire.
For details on cleaning the electrostatic
charger wire, refer to “Electrostatic
charger wire” on page 10-7.

1

Open the machine’s front door.

«
...
414
415
416
417
418
...
»

Содержание d-Color MF25












































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для d-Color MF25

Бренд: Olivetti Страницы: 2

Бренд: FujiFilm Страницы: 9

Бренд: Triumph Adler Страницы: 153

Бренд: Oce Страницы: 122

MultiXpress X4 Series

Бренд: Samsung Страницы: 609

Бренд: Panasonic Страницы: 187

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды