background image

30

     PROPER SELECTION OF THE POWER SUPPLY CORD

If no power supply cord is provided, please select the proper power supply cord for the equipment by referring to “ Specifications ” and
“ Certified Cord ” below:

CAUTION:

In case you use a non-approved power supply cord for Olympus products, Olympus can no longer warrant the
electrical safety of the equipment.

Specifications

Voltage Rating

Current Rating

Temperature Rating

Length

Fittings Configuration

125V AC (for 100-120V AC area) or, 250V AC (for 220-240V AC area)

6A minimum

60°C minimum

3.05 m maximum

Grounding type attachment plug cap. Opposite terminates in molded-on IEC con-

figuration appliance coupling.

Table 1  Certified Cord

A power supply cord should be certified by one of the agencies listed in Table 1 , or comprised of cordage marked with an
agency marking per Table 1 or marked per Table 2. The fittings are to be marked with at least one of agencies listed in
Table 1. In case you are unable to buy locally in your country the power supply cord which is approved by one of the
agencies mentioned in Table 1, please use replacements approved by any other equivalent and authorized agencies in
your country.

Country

Agency

Certification

Mark

Country

Agency

Certification

Mark

Argentina

Australia

Austria

Belgium

Canada

Denmark

Finland

France

Germany

Ireland

IRAM

SAA

ÖVE

CEBEC

CSA

DEMKO

FEI

UTE

VDE

NSAI

Italy

Japan

Netherlands

Norway

Spain

Sweden

Switzerland

United
  Kingdom

U.S.A.

ASTA
BSI

UL

IMQ

KEMA

NEMKO

AEE

SEMKO

SEV

JET, JQA , TÜV,
UL-APEX / MITI

Содержание CKX41









































Отзывы: