OLIMEX OLIMEXINO-85 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 24

OLIMEX OLIMEXINO-85 Скачать руководство пользователя страница 21

OLIMEX© 2015

OLIMEXINO-85 user's manual

CHAPTER 7: REVISION HISTORY AND SUPPORT

7. Introduction to the chapter

In this chapter you will find the current and the previous version of the document you are reading.
Also the web-page for your device is listed. Be sure to check it after a purchase for the latest
available updates and examples.

7.1 Document revision

Revision, date

Changes

Modified page

A, 27.11.13

Initial manual release

All

B, 31.01.14

Adjusted manual to fit the changes
of the USB connector

Multiple

C, 02.07.15

Updates regarding the bootloader
used

Multiple

D, 07.07.15

Fixed wrongfully suggested fuse
settings

Multiple

7.2 Board revision

Remember to check the schematics and the board design files to compare the differences.

Revision

Notable changes

A

Initial release of the board

B

1 USB mini connector was changed to USB type B
2 Added RST_E jumper (in open position by default) instead of
removing the RST pin from the extension.
3 R6(NA) pads are now added to the RST line just in case a
resistor is needed

Page 21 of 23

«
...
19
20
21
22
23
...
»

Содержание OLIMEXINO-85

























Отзывы:

Нет отзывов