CAS-24V-ZHAGA-4P-40-DA / CAS-24V-ZHAGA-4P-80-DA-LX
OLFER
EN-V0.4 13 Feb 2023
3
Installation instructions
Instrucciones de instalación
Disconnect the supply voltage before installing the control nodes. Install the node upright on the
ZHAGA book 18 socket (not included) to prevent water from entering between node and socket.
Insert the node into the socket and turn it clockwise to fix it.
Lighting outdoor installations must incorporate surge protective devices against atmospheric
discharges.
Input voltage 24VDC must be isolated from mains (SELV). The control nodes generate the voltage
required for the DALI bus. Check that wiring of the base socket matches the node wiring diagram.
Follow DALI installation requirements. Total DALI bus current must not exceed 250mA. DALI D4i drivers
have their internal DALI power supply ON by default, so it is likely that when several D4i drivers are
connected to the same DALI bus, they will need to be reprogrammed to deactivate their internal
DALI power supply.
The adequate profile must be selected before pairing the unit to a Casambi net. Consult the
datasheet for the profiles list.
Most profiles can do an automatic DALI initial addressing and configuration of the DALI drivers and
external sensors. Drivers and sensors should be previously connected to the DALI bus and powered
for this initialisation operation. It is also possible to launch the initialisation configuration procedure
and also set DALI addresses and groups at a later time by using the Casambi App.
Do not place the nodes inside any metallic enclosure types (Eg: metallic luminaires or cabinets).
Do not place the nodes under ground or at ground level (this will reduce the range drastically).
Metal structures (poles), walls, and photovoltaic panels produce shielding of radio frequency
communications. Locate the nodes so that there are no obstacles between them (with line of sight
between nodes).
When the node is installed and powered, it can be configured and paired to a net using Casambi
App. The node must be within the Phone or tablet Bluetooth range for this.
Unpaired nodes will appear in nearby devices list of Casambi App. Select the most suitable profile
for the application before pairing the node to a net.
CAS-24V-ZHAGA-4P-80-DA-LX incorporates a light sensor. Light sensor sensitivity, tolerance/threshold
and calibration can be adjusted with the App. For best results, calibration should be done by using
sun light within the available light level range of the incorporated sensor.
Desconecte la tensión de alimentación antes de instalar los nodos de control. Instale el nodo en
posición vertical sobre el zócalo para evitar la entrada de agua entre nodo y zócalo. Inserte el
nodo en el zócalo y gírelo en el sentido de las agujas del reloj para fijarlo.
Las instalaciones de alumbrado exterior deben incorporar dispositivos de protección contra las
descargas atmosféricas.
La tensión de entrada de 24Vcc debe estar aislada de la red (SELV). Los nodos de control generan
la tensión necesaria para el bus DALI. Verifique que el cableado del zócalo de montaje coincida
con el esquema de conexión del nodo.
Siga la normativa de instalación DALI. La corriente total del bus DALI no debe exceder los 250mA.
Los drivers DALI D4i tienen su fuente de alimentación DALI interna activada por defecto, por lo que
es probable que cuando varios drivers D4i estén conectados al mismo bus DALI, deban
reprogramarse para desactivar su fuente de alimentación DALI interna.
El perfil adecuado debe ser seleccionado antes de vincular el equipo a la red Casambi. Consulte
la lista de perfiles disponibles en la ficha técnica.
La mayoría de los perfiles pueden realizar una configuración y un direccionamiento inicial DALI
automáticos de los drivers y sensores externos DALI. Los drivers y sensores deben estar previamente
conectados al bus DALI y alimentados para esta operación de inicialización. También es posible
