background image

6.  Connect PC to Gateway
 

a. USB to Serial Adapter (SX1000-CC9)

 

b. Gateway Configuration Cable (SX1000-CC1)

7.  Identify COM Port for use in BreeZ® (Device Manager)

8.  Select a Gateway in BreeZ® Project Tree

9.  Update Gateway with BreeZ® Project File

10. Confirm Gateway “Configuration Download OK” in 
       Build Tab Window in BreeZ®

11. Save Project File onto Gateway (For Backup) 

 

4. Configuration Sequence - continued

2. Required Items

- DH1 - Base Unit Wireless Gateway
- External Power Source for Base Unit (9-30 VDC)
- Antenna for Gateway (Bulkhead, Omni, or Yagi)
- Antenna Cable (N to MMCX Connector)
- N to N Antenna Cable and Lighting Arrestor (Optional)
- External Enclosure for Base Unit (NEMA)
- DIN Rail (35 mm)

- USB to Serial Adapter (SX1000-CC9)

- Gateway Configuration Cable (SX1000-CC1)
- BreeZ® Configuration Software v5.0 or Higher

- PC
- S

crewdriver Set + Technician’s Screwdriver

- Any Additional Tools for Installation
- RS485 I/O Expansion System (Optional)

 

CAUTION

: Field wiring connections shall be made in accordance

              with Article 504 of the National Electrical Code, ANSI/NFPA70.

 CAUTION

: The Base Unit must be installed within an enclosure

 

that requires a tool to access. This is to prevent inadvertent

disconnection of any of the power wiring, signal wiring or

communication cables.

ATTENTION

: Le 

Base Unit doit être installé dans une enceinte qui nécessite

un outil d'accès. Ce est pour éviter toute déconnexion accidentelle de l'un

des câbles câblage de puissance, câblage ou de communication signaux.

 WARNING

: Ensure installation of the Gateway meets applicable

 

state and national electrical code requirements. The installation

of the Base Unitshould only be performed by a qualified installer or a

factory representative.

AVERTISSEMENT

: Veiller à l'installation de la passerelle répond Etat et

des exigences nationales de code de l'électricité. L'installation de la

Base Unit ne doit être effectuée par un installateur qualifié ou un

représentant de l'usine.

 WARNING

: To prevent ignition of flammable or combustible

 

atmospheres, disconnect power before servicing.

AVERTISSEMENT

: Pour éviter l'inflammation d'atmosphères inflammables

ou combustibles, débrancher l'alimentation avant l'entretien.

 WARNING

: EXPLOSION HAZARD – Substitution of components

 

impair suitability for Zone 2.

AVERTISSEMENT

: RISQUE D'EXPLOSION - Le remplacement de composants

nuire à la conformité pour la Zone 2. 

 WARNING

: EXPLOSION HAZARD – Do not separate/disconnect

 

connectors when energized.

AVERTISSEMENT

: RISQUE D'EXPLOSION - Ne pas séparer / débrancher les

connecteurs lorsque excité. 

 WARNING

: EXPLOSION HAZARD – Do not service when an

 

explosive atmosphere is present.

AVERTISSEMENT

: RISQUE D'EXPLOSION - Ne pas service lorsque une

atmosphère explosive est présente.

 WARNING

: EXPLOSION HAZARD – Do not use reset switch in

 

hazardous area.

AVERTISSEMENT

: RISQUE D'EXPLOSION - Ne pas utiliser le commutateur

de réinitialisation en zone dangereuse.

1. Before You Begin

1.  Download and install latest BreeZ® Software v5.0 or
      higher to a PC (see section 3) 

2.  Check for latest Base Unit Firmware on Download Center

3.  Create a BreeZ® Project File

*4.  If upgrading Firmware, follow these instructions:
 

a. Physically Connect Gateway to PC

 

b. Supply power

 

c. Open Connect screen and click “Flash”

 

d. Locate new Firmware file and click “Open”

 

e. DO NOT DISCONNECT OR TURN POWER OFF while

 

     upgrading Firmware (It may take a few minutes for

 

      upgrading process to finish)

 

f. Wait until LED turns off

5.  Power up Gateway (9-30Vdc) and wait until boot-up
     sequence is complete 
 

(LED will turn off once boot-up is complete)

3. 

Configuration Sequence 

80-3103-001_J

This guide provides basic information to assist you in quickly

getting started. Go to www.OleumTech.com to download the

full User Guide for detailed installation and other information.

5. Installation Sequence

1.  Install Gateway inside a NEMA enclosure
 

a. 

Remove Cover Using Two Top Screws.

 

b. 

Adjust and Tighten DIN Rail Clamp

 

c. 

Reattach Cover

2.  Follow best grounding practices

3.  Setup and connect an Antenna with Lightening Arrestor

      to Gateway

4.  Connect Gateway to third-party Serial device(s)

5.  Power up Gateway

6.  Power up/reboot any impacted sensors/devices if necessary

7.  Verify RF and data communications
 

a. Use Modbus Register Polling and Write features in BreeZ®

 

b. Verify communication from third-party device(s) or

 

    SCADA system 

QUICK START GUIDE

BASE UNIT - WIRELESS GATEWAY (DH1)

Отзывы: