Okolab UNO-T Скачать руководство пользователя страница 61

Страница: 61 / 73

Note

►

If you forgot the password, use the restore password reported on the certificate attached to UNO-

CONTROLLER.

To change the password, press on the icon

(see Figure 91) and follow the indications that will appear.

Figure 91. Settings

–

Password - Change password.

8.2.8.8

Summary

Press on the Summary icon

(see Figure 92 a) to enter the summary page, which reports technical

information.

Figure 92. How to enter the Summary page (a

–

b).

Note

►

This page contains data useful for technical/control reasons. In case you requested support from one

of Okolab engineers you may be asked for some of these data.

8.2.8.9

Auto on/off

UNO-CONTROLLER can be programmed to turn on and/or turn off automatically at specific times. Press

Auto on/off icon

(see Figure 93 a) to enter Auto on/off menu (see Figure 93 b).

Содержание UNO-T










































































Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды

Okolab UNO-T, Руководство пользователя

Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды