Oklahoma Sound
INTRODUCTION
Congratulations!!! On your purchase of the Model #SK Sound Kit. This kit
will easily transform your lectern into a sound unit, allowing your presenta-
tion to be amplified and heard by everyone in the audience. The kit is easy
to install in a matter of minutes and can be removed
2
Kit includes:
1 Series 100 amplifier.
2 Speakers.
1 Handheld microphone.
1 Tie clip microphone.
1 Goose neck with base and microphone holder.
2 Velcro strips for speaker.
1 Velcro strip for amplifier.
4 Small screws to secure amplifier.
1 Easy connect wire.
IMPORTANT SAFTEY INFORMATION
As with any electric/electronic device, care should be taken during use.
ALWAYS turn off the amplifier before opening or servicing any part of
the unit. Please handle your lectern with the care it deserves.
Manufactures Warranty
Our lecterns undergo the most rigid and exacting test for superior quality and performance before leaving our factory.
Oklahoma Sound warrants this product to be free from defective material and workmanship on this unit for five years
from the date of resale by an authorized Oklahoma Sound distributor. Oklahoma Sound will replace defective parts and
repair malfunctioning products under this warranty when the defect occurs under normal installation and use, provided
that the unit is returned to our factory via prepaid transportation after direct authorization and approval form Oklahoma
Sound. This warranty provides that examination of the returned product must disclose in our judgment a manufacturing
defect. This warranty does not extend to any product which has been subject to misuse, neglect, accident, improper in-
stallation or where the serial number has been removed if defective and is given in lieu of any other warranty implied or
expressed and will not cover any damage.
Also available from Oklahoma Sound
Model SK-B
Model SK-B is a bracket system that will mount the speakers to the lectern
providing the option of having the speakers swivel to your desired angle.
Note: The brackets will have to be screwed to the side panels of the lectern.
Oklahoma Sound
3
Speaker Assembly:
Diagram 1
1. Begin by locating the 2 small caps on both sides of the
side panels. Gently pull them out by using a flat screw-
driver or similar tool. USE CAUTION to avoid scratching
the panels.
Amplifier Installation
1. Remove amplifier from carton and place on a flat surface.
Attach the easy connect wiring to the back of the amplifier.
See Diagram 1. Once attached be sure that the double wire
is split into two to enable attachment to both right & left
speakers.
2. Once the plug is fastened to the back of the amp, secure
the amplifier to the middle shelf. (See Diagram 2 for rec-
ommended location.) The amplifier can be attached by ei-
ther using the self adhesive Velcro strip or by screwing to
the shelf. To screw the amplifier to the shelf insert the four
provided screws through the two holes on both sides of
the amplifier chassis and tightly screw in using a power
tool.
Speaker installation
1.
1.
1.
1.
Remove both sets of Velcro strips from the carton.
2.
2.
2.
2.
Each set of Velcro Strips is made up of two parts. One side
is to adhered to the lectern and the other to the speaker.
3.
3.
3.
3.
Remove the plastic from the back of the side that you in-
tend to adhere to the lectern and firmly stick to side panel
See diagram 3 for correct Velcro location.
4.
4.
4.
4.
Carefully remove speakers from carton. Continue by re-
moving the plastic backing from the back of the Velcro and
firmly stick it to the side of the each speaker. Be sure to
stick the Velcro on the correct side of the speaker. For the
speaker you intend to place on the right side of the lectern,
the Velcro must be placed to the left side of the speaker,
and visa-versa opposite for the left speaker.
5.
5.
5.
5.
Once both sides of Velcro strips are in place, firmly join the
speaker to the lectern. See Diagram 4 for the proper speak-
er placement on the side panel.
NOTE: For best results, let the Velcro stick to unit for 24 hours
before attaching the speaker to the lectern.
Wiring
1.
1.
1.
1.
Begin by taking both sides of the easy-connect wire,
which is now connected to the back of the amplifier, and
feed each ends of the wires from the inside of the unit,
through the holes on each of the side panels.
2.
2.
2.
2.
Once the two ends have been properly fed through the
panels, secure the wires to the terminals located at the
back of the speakers. To properly secure wires to terminal,
loosen plastic caps to expose terminal hole and insert wire.
Once inserted, tighten plastic caps. IMPORTANT: One end
of the wire should be attached to the BLACK terminal on
the right speaker and the other wire should be attached to
the RED terminal on the left speaker. (See diagram 5).
3. Proceed by feeding the single bridge wire from the inside
of the unit through the holes on each of the side panels.
Connect the wire to the RED terminal on the right speaker
and to the Black terminal on the left speaker .
Diagram 2
IMPORTANT:
Do not install Sound Kit until your lectern is fully assembled.
Diagram 4
Diagram 5
Diagram 3
