SEM-7540LPDN_rev010709
V
S.A.G.C./A.G.C. Mode Switch
S.A.G.C.: When camera has installed at low light condition. The
sensitivity of the camera rises (26dB).
A.G.C.:
26dB
*
In order to activate D/N function
(Color mode automatically switches
to B/W mode under 2.0 Lux),
please switch to S.AGC.
Ϥ
11
SYNC MODE: Switch
L.L. MODE: It synchronizes the video signal between cameras using
the frequency of the power supply without external synchronous
generator.
INT MODE: The camera maybe operated independently with the
internal crystal control.
Ϥ
12
V.P (Vertical Phase Adjuster)
This is used to adjust the vertical phase of the video output signal.
Ϥ
13
VIDEO Connector
This is an output for connecting to a video monitor or recorder (75).
Ϥ
14
Power Input Terminal
Connect the power supply of 12V DC or 24V AC.
Model SEM-7540LPDN
SEM-7540LPDNP
TV System
NTSC PAL
Image Sensor
1/3” Sony Exview CCD
DSP
Sony HQ-1
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Video Output
1.0Vp-p Composite / 75ohms
Resolution
540 TV Lines
Minimum
Illumination
0.05 Lux @ F1.0
Color mode automatically switches
to B/W mode under 2 Lux
Day & Night
Switching
Mechanical IR Cut Filter (ICR) Auto Switching
Color/Monochrome
Infrared
Sensitivity
700~1100nm
Scan System
2:1 Interlace
Synchronization
Internal/Line Lock (AC Version Only)
S/N Ratio
More than 50dB (AGC OFF)
Electronic
Shutter Speed
AES ON: 1/50(60)~1/100,000sec
AES OFF: 1/50(60)sec, FL 1/120(100)s, 1/250sec,
1/500sec, 1/1000sec, 1/2000sec, 1/4000sec,
1/10000sec
Back Light
Compensation
ON/OFF Switchable
Auto Gain Control
ON/OFF Switchable
White Balance
AWB
Lens
Not Included
Lens Mount
CS/C (with Adaptor)
Auto Iris Control
DC/Video Switchable
Power Supply
12V DC / 24V AC
Power
Consumption
210mA / 3.5W
Operation
Temperature
14
q
F ~ 122
q
F / -10
o
C ~ +50
o
C
Storage Humidity
RH 85% or less
Storage
Temperature
-4
o
F ~ 140
o
F / -20
o
C ~ +60
o
C
Dimension
4.72”(L) x 2.36”(W) x 1.97”(H)
120mm(L) x 60mm(W) x 50mm(H)
Weight
0.88 lbs / 400g
*Specifications are subject to change without notice
z
One (1) SEM-7540LPDN/SEM-7540LPDNP Camera
z
One (1) Allen Wrench
z
One (1) CS Adaptor Ring
z
One (1) Operational Manual
*
For any returns, please include all components listed above with
original packaging in
Resalable Condition
.
Absolutely No Returns
will be accepted if any component is missing/damaged or if any cable is
cut or tampered with.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this
may damage the pick-up device.
2.
Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could
damage the camera.
3.
Requires a proper operating environment
This camera is designed for outdoor or indoor use. The allowable
temperature range for operation of this camera is between
14
q
F ~ 122
q
F / -10
q
C ~ 50
q
C and the allowable humidity is 85%RH
maximum.
4.
Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before
lens installation or whenever the lens is changed. Cleaning should be
done by using a chamois, a very fine soft cloth, lens tissue, or cotton
tipped applicator and ethanol to carefully remove any fingerprint or
dust.
5.
Check the power source voltage
The power source voltage should be within the specified range.
(Camera must meet the specifications). Camera must be connected to
a surge protector at all times.
6.
Objects and liquid entry
Never push objects of any kind into this camera as this may touch
dangerous voltage points of short out parts that could result in a fire
or electric shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
8.
Damage requiring service
Unplug this video product from the wall outlet and refer service to
qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video
product.
c. If the video product has been dropped or the cabinet has been
damaged.
d. When the video product exhibits a distinct change in
performance.
OKINA USA products are covered under warranty for one year from the
date of purchase. The war
r
anty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any
information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial
number on the camera sticker; therefore, it should not be removed.
2. Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not
described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with.
Cutting or modifying of the cables will result in termination of the
warranty.
CAUTION
WARRANTY
SPECIFICATIONS
LIST OF COMPONENTS
