Oki ML5590/91 Скачать руководство пользователя страница 27

Страница: 27 / 96

USING YOUR PRINTER > 27

PRINTER RESET

Clearing some error conditions requires that you reset (reinitialise)
the printer. To do this:

Press and release

SEL

(1) to take the printer off line.

The

SEL

light goes out.

Press and hold

SHIFT

(2), then press the

RESET/CHARACTER

PITCH

key (5).

EMULATIONS

Epson

LQ — factory setting

IBM

Proprinter

IBM

AGM

Changing Emulations

Make sure paper is loaded.

Press and hold

SHIFT

(2), then press

SEL

(1).

Press

(3).

The following line will print:

Printer Control

Emulation Mode

EPSON LQ

Press

TEAR

(4) repeatedly until the emulation you wish to

select prints in the right-hand column.

NOTE

Pressing

SHIFT

and

RESET

reinitialises the printer, but does

not

affect

any menu settings and does

not

reset the printer to the factory defaults.

For information on resetting the printer to the factory defaults, see
“Resetting the Menu to the Factory Defaults” later in this chapter.

Содержание ML5590/91

































































































Результаты поиска

Содержание ML5590/91

Отзывы:

Oki ML5590/91, Руководство пользователя, Страница: 27 / 96

Результаты поиска

Содержание ML5590/91

Отзывы: