Oki B6200 Series, Руководство по обслуживанию

Страница: 28 / 679

1 - 12
Chapter 1 Troubleshooting
012 953 FaceUP Tray Close
Detect that Faceup Tray is closed though printing out to Faceup Tray is
specified.
Dirt or defect of Sensor Face Up Open
FIP1.43
(Separate
volume)
012 969 IOT Center Tray Full
Detect paper left in the offset ejecting tray.
Remove paper in IOT Face Down Tray.
Dirt or defect of Sensor Full Stack
016 450 Same SMB host name
The same host names of PCs exist on the network.
Change host name.
-
016 452 Same IP address
The same IP address of PCs exist on the network.
Check and change the IP address.
-
016 453
Fail to acquire IP DHCP
server Fail to acquire IP address from DHCP server.
Set IP address. (Do not acquire from DHCP)
-
016 460 HDD Full
When accessing HD, Detect HDD Full status.
Enter the Diag Program Hard Disk, and examine the trouble of DC355
Hard Disk.
-
016 500
SMTP Server Address
Resolution Fail for Mail IO SMTP server name is not correct.
Set SMTP server name correctly or set by IP address.
-
016 501
POP Server Address
Resolution Fail for Mail IO POP3 server name is not correct.
POP3 server name correctly or set by IP address.
-
016 502
POP Authentication Fail
for Mail IO
The certification information (user name and password) of POP3 is not
correct.
Set the certification information (user name and password) of POP3.
-
016 503
SMTP Server Address
Resolution Fail for
Redirector
SMTP server name is not correct.
Set SMTP server name correctly, or check the setting of DNS server.
-
016 504
POP Server Address
Resolution Fail for
Redirector
POP3 server name is not correct.
POP3 server name correctly, or check the setting of DNS server.
-
016 505
POP Authentication Fail
for Redirector
The certification information (user name and password) of POP3 is not
correct.
Set the certification information (user name and password) of POP3.
-
016 701 Out of Art EX Memory
Detect insufficient memory for PLW process when using ART EX.
Print with low resolution if it is possible. (Print mode [normal])
-
016 702 Cannot Compress at all
Printing ART EX is not available due to the lack of print page buffer.
Print with low resolution. (Print mode [normal])Add memory.
Add print page buffer.
Use page printing mode.
-
016 703
Email Received To Invalid
Box
When receiving E-Mail, unopened or invalid personal box number is
specified.
Send e-mail to the valid personal box.
Open the new personal box.
-
016 704 Mailbox is Full
Detect personal box full (it reaches the maximum number of messages
in one box. (Job end)
Delete unnecessary message, and start the job again.
-
016 705
Secure Print Storage
without HD Fail to resister the security print because HDD is not installed.
Check that HDD is installed.
-
016 706
Max. User Number
Exceeded
Over the maximum number of users of security/sample print.Delete
unnecessary message and registered users of security print, and print
again.
-
016 707 Sample Print Fail
Fail to register sample print because HDD is not installed or it is failure.
Check that HDD is installed.
Enter the Diag Program Hard Disk, and examine the trouble of DC355
Hard Disk.
-
016 709 ART EX Command Error
When processing PLW, ART EX command error causes.
Cancel the job, and execute the job again.
-
016 710 Delayed Print Fail
Delete the condition to make impossible Delay Print.(Install HD and so
on)
-
Chain Link Fault Items Conditions of detect/Methods of treatment Ref FIP