manualshive.com logo in svg

OilGear PVM-011, Инструкция по эксплуатации, Страница: 20 / 64

Поделиться
Скачать
OilGear PVM-011 Скачать руководство пользователя страница 20

20

THE OILGEAR COMPANY

Bulletin 947070-B

ROTATING GROUP

The rotating group may be heavy. Be
careful not to damage cylinder wear
surface which mates against the valve
plate, bearing diameters or piston shoes.
Use proper lifting techniques and
assistance from others to prevent
personal injury.

1.   Remove  O-rings  (13 and 14) from the pump

housing (1). Do not remove roll pins (12) unless
they are damaged.

2.  Remove the rotating group by turning the

driveshaft (21) slowly, while pulling the cylinder
barrel (38) from the housing.

3. 

 Identify (number) each pump piston shoe

assembly  (39) and its respective bore in the
cylinder barrel (38) and shoe retainer plate (40)
for easy reassembly.

4.   See  Figure 9. Lift out shoe retainer (40) with

pistons  (39) and remove the fulcrum ball (41)
and shoe retainer spring (42).

Figure 9. Rotating Group Disassembly 

-011/-014/-022

5.   Remove cylinder barrel retaining ring (37) and

pull the hydrodynamic cylinder bearing (35) and
roll pins, if necessary, from the housing.

-025/-034/-046/-064/-065/-075/
-076/-098/-130

5.  Remove the hydro-bearing retaining ring (37).

6. Remove socket head screw (36) and lock

washer (5).

7. Pull hydrodynamic cylinder bearing (35) from

housing.

DRIVESHAFT GROUP

1. Remove the drive key (22 or 23), if used and

the driveshaft bearing retainer ring (28).

2.   Grasp outboard end of driveshaft (21) and pull

it out of the pump housing.

3. Remove shaft seal retainer (25). Remove

driveshaft seal (24) from housing ONLY if
necessary.

If the seal is removed it can not be reused.
It must be replaced.

SWASHBLOCK GROUP

1. Remove the socket head cap screws (34), the

housing cover (33) and O-ring (32).

2. Reach into the housing through the opening

and pull out the swashblock (29), along with
control pin (31).

The saddle bearing (30) is seated in the housing by
an integral pintle that engages a hole in the
housing.

3. Pull the saddle bearing (30) back (parallel to

driveshaft axis) until the pintle disengages from
the housing, then pull the saddle bearing out in
the same manner the swashblock was
removed.

!

WARNING

38

42

41

39

40

OILG0023

NOTE

Содержание PVM-011

































































Отзывы:

Нет отзывов