OHAUS VXHDAL Скачать руководство пользователя страница 4

3

S

AFETY

 I

NSTRUCTIONS

Please read the entire instruction manual before operating the Vortex Mixer.

WARNING! DO NOT use the Vortex Mixer in a hazardous atmosphere or 
with hazardous materials for which the unit was not designed. Also, the 
user should be aware that the protection provided by the equipment may 
be impaired if used with accessories not provided or recommended by 
the manufacturer, or used in a manner not specified by the manufacturer.

Always operate unit on a level surface for best performance and 
maximum safety.

DO NOT lift the Vortex Mixer by the head. All heads, including cup head, 
are removable. They can pop off if lifted by them. 

CAUTION! To avoid electrical shock, completely cut off power to the unit 
by disconnecting the power cord from the wall outlet. Disconnect unit from 
the power supply prior to maintenance and servicing.

Spills should be removed promptly. DO NOT immerse the unit for 
cleaning.

DO NOT operate the unit if it shows signs of electrical or mechanical damage.

Earth Ground - Protective Conductor Terminal
Alternating Current

EN

S

TANDARDS

 & R

EGULATIONS

Compliance to the following standards and regulations is indicated by the corresponding mark 

on the product.

Mark

Standards and Regulations

OHAUS Corporation declares that the VXHD, VXMP series mixers comply with direc-

tives 2011/65/EU, 2014/30/EU, 2014/35/EU and standards EN 50581, EN 61010-1, 

EN 61010-2-051, EN 61326-1.

The full text of the EU declaration of conformity is available at the following 

internet address

This product complies with directive 2012/19/EU.  Please dispose of this product in 

accordance with local regulations at the collecting point specified for electrical and 

electronic equipment.  

For disposal instructions in Europe, refer to 

EN 61326-1

CAN/CSA C22.2 61010-1, CAN/CSA C22.2 61010-2-051

UL 61010-1, UL 61010-2-051

Global Notice

Warning: This is a Class A product. In a domestic environment this product may cause radio interfer-

ence in which case the user may be required to take adequate measures.

Canada Notice

This Class A digital apparatus complies with Canadian ICES-003.

FCC Notice

NOTE:  This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a commercial envi-

ronment.  This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause harmful interference to 

radio communications.  Operation of this equipment in a residential area is likely to cause harmful 

interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by Ohaus Corporation could void the user’s authority 

to operate the equipment.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание VXHDAL












Отзывы: