manualshive.com logo in svg

OETIKER CC 20, Инструкция по эксплуатации, Страница: 26 / 58

Поделиться
Скачать
OETIKER CC 20 Скачать руководство пользователя страница 26

 

Clamp pincer CP 10 / CP 20 / CC 20 

5 Use of the clamp pincer 

Issue 06.19 

08902961 

5-26 

NOTICE 

• 

When the battery is low, the pincer will not perform closures. 

• 

This display should be used only to indicate the charge remaining. 

• 

The battery can remain in the clamp pincer CP 10 / CP 20 / CC 20 whilst the charge status is being 
checked. In order to avoid uncertainty about the accuracy of the reading, however, clamp pincer CP 10 / 
CP 20 / CC 20 must be switched off for at least 1 minute prior to the test. 

 

 

5.2.2 

Battery charging 

INFO 

Further information about the battery charger can be found in the instruction manual from Techtronic 
Industries GmbH. 

 

1.  Connect charger (Fig. 10/2) to power supply. 

2.  Attach battery (Fig. 10/1) to battery charger. 

3.  Remove the battery (Fig. 10/1) from the battery 

charger as soon as it has reached the desired 
charge status. 

4.  After charging, disconnect the battery charger 

(Fig. 10/2) from the power supply. 

 

Fig. 10:  Charging the battery 

 

5.2.3 

Inserting battery 

 

CAUTION 

Risk of injury due to accidentally pressing the START button! 

Once the battery has been inserted, the pincer is ready for use. If the START button is pressed (even 
accidentally) the pincer jaws will close! 

 

Ensure the START button is not pressed accidentally. 

 

Содержание CC 20



























































Отзывы:

Нет отзывов