3
Operating Instructions and Parts Manual
OEM24875
5/20
2020 OEMTOOLS
®
36" TILT BARREL FAN
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
Thoroughly read and understand all instructions in this
product manual before using this product. Failure to
follow all instructions listed below may result in electric
shock, fire, and/or serious personal injury.
WARNING
1. Unplug the fan before moving it or performing
maintenance. DO NOT touch the fan when your hands
are wet.
2. Those who are not qualified electricians should not
disassemble, repair or rebuild the fan.
3. Unplug the fan when it is not in use.
4. DO NOT unplug the fan by holding the cable cord.
Unplug by holding the plug.
5. DO NOT use the fan when there is damage to the cable
cord or plug.
6. Avoid the use of extension cords when possible.
Ensure that they are UL listed if they must be used.
DO NOT use a single extension cord to operate more
than one fan. DO NOT plug the fan into any other
cord-connected device (power strip, surge protector,
multiple outlet adapters etc.).
7. DO NOT use the fan close to any fire or heat source.
8. DO NOT insert your hand or other objects into the
guard or the movable parts.
9. To reduce the risk of fire or electric shock, DO NOT use
this fan with any solid-state speed control device.
10. DO NOT use this fan outdoors.
11. DO NOT operate any fan with a damaged cord or plug.
Discard fan or return it to an authorized service facility
for examination and/or repair.
12. DO NOT run cord under carpeting. DO NOT cover cord
with throw rugs, runners, or similar coverings. DO NOT
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
13. DO NOT use if electrical cord is frayed or bent.
CAUTION
14. DO NOT immerse the fan.
15. Fit the guard onto fan before starting up the fan.
16. This fan is not intended for use by people (including
children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
unless they have been given supervision or instructions
concerning use of the fan by a person responsible for
their safety. Supervise children to ensure they do not
play with the fan.
17. Always place the fan on a stable, flat, level surface
when operating, to avoid the chance of the fan
overturning.
18. DO NOT immerse fan in water.
OPERATING INSTRUCTIONS
1. The fan comes with two different speeds.
2. Switch the fan ON by turning the knob to speed 1 or 2.
3. To switch the fan OFF, turn the switch knob to 0.
4. Before operating, assemble the wheel according to the
instruction of wheel assembly drawing.
WARNING:
DO NOT depend on the ON-OFF switch
as the sole means of discontinuing power when installing
or servicing the fan. Always unplug the power cord.
CARE AND MAINTENANCE
Unplug the appliance before cleaning. DO NOT use any
water for cleaning metal surfaces. Using a soft cloth, wipe
off the surfaces of the fan. To clean dust off the grill, use a
vacuum cleaner or take off the front grill by removing the
securing screw on the edge of the grill with a screwdriver.
After cleaning, remount the grill and fasten the securing
screws on the edge of the grill.
WHEEL ASSEMBLY
Product assembly drawing
Wheel assembly drawing
Picture 2
Picture 1
1
2 3
10 4 5 7 9 8
6
7
7
11
12
13
1
14
15
2
9
3 5 4
6
8
7
17
16
10
1. Remove the wheels from packing, then press and fold
the packing.
2. Put the Folded Packing (5) under the Square Tube (4) to
hold up the Tilt Barrel Fan (picture 1).
3. Put the Wheel Shafts (3 and 8) into the two Holes (9
and 10). Line up the Holes on the Wheel Shafts and
then insert the Split Pin (7) (picture 2).
4. Split the Split Pin (7) to avoid the Split Pin coming loose.
DISPOSAL
At the end of the useful life of the OEMTOOLS
®
36" Tilt
Barrel Fan, dispose of the components according to all
state, federal, and local regulations.
