3
Operating Instructions and Parts Manual
24950
1100 LB.
ENGINE SUPPORT BAR
2/18
2018 OEMTOOLS
™
7. DO NOT move the vehicle, engine or engine supports
while the Engine Support Bar is supporting the weight
of the Engine.
8. DO NOT leave the engine suspended for long
periods of time. This tool is intended for use during
maintenance, not for engine storage.
9. ALWAYS inspect the Engine Support Bar before each
use. Discontinue use immediately if the unit is bent,
broken or damaged in any way.
10. Imbalanced loading, swinging or sudden drops
can generate dynamic loading, which may lead to
product failure.
11. Personal Protective Equipment: ALWAYS wear ANSI
approved impact safety goggles, a full-face impact
rated safety shield and heavy-duty work gloves while
performing any vehicle maintenance or repair.
ASSEMBLY INSTRUCTIONS
1. Unpack all items from the box and reference the
parts list to ensure all parts are present before
continuing installation.
2. Place all parts onto a clean, protected work surface.
3. Place the Rubber Bases (10) onto each end of the
Standing Bracket (9).
4. Place the Standing Bracket (9) within the inlet of the
Standing Block (8). Align the holes on the Bracket
(9) and the Block (8) and secure with the Standing
Bracket Bolt (7).
5. Insert the threaded end of the Standing Bracket
assembly (completed step # 4) into the gap on one end
of the Beam (1).
6. Place a Lock Knob Washer (3) over the threaded end of
the Standing Bracket assembly. Fasten the assembly
using a Lock Knob (2).
7. Repeat steps 3-6 to assemble the second Standing
Bracket.
8. Insert the threaded end of the J-Hook (11) into the
center gap of the Beam (1). Place a J-Hook Washer (6)
over the threaded end, and fasten with the Grip Handle
(5). Repeat for the second J-Hook (11).
NOTE: It is not necessary to tighten the Grip Handle
completely. The Grip Handle/J-Hook assembly defines
the engine support height.
9. Place the Handle Sleeves (4) over each end of the Grip
Handles (5).
10. Hang each Chain (12) from the J-Hooks (11).
OPERATION INSTRUCTIONS
WARNING
:
OEMTOOLS
™
is not responsible for
damage to the vehicle or paint finish. The user must
understand that by using this product, they are accepting
the risks involved with vehicle maintenance and repair.
There are outlying factors that cannot be discussed
or defined by this product manual. Always refer to the
vehicle maintenance manual, and utilize best judgment
prior to attempting any maintenance or repair.
1. Park the vehicle on a flat surface. Apply the parking
brake and chock the wheels.
2. Allow the engine to cool sufficiently prior to repair or
maintenance.
WARNING
:
Working on hot engine components can
cause serious injury.
3. Inspect the inner fender channel for a flat area that
can support the weight of the engine and the Engine
Support Bar.
WARNING
:
DO NOT place the supports on the outer
fender. This can cause damage to the vehicle and may
lead to product failure.
4. Center the Engine Support Bar over the Engine and
extend the Standing Brackets to the points identified
in Step # 3. Ensure the Standing Brackets are securely
tightened in place after adjustment.
5. Attach the Engine Support Chains to the engine.
NOTE: Reference the vehicle maintenance manual to
identify the proper lifting points.
6. Attach the ends of the chains to the J-Hooks.
7. Slowly rotate the Grip Handles clockwise until the chains
are taut and the engine is held evenly and securely.
8. While loosening the engine mounts, adjust the Grip
Handles with ¼-inch turns until the engine’s weight is
supported and evenly distributed between the two chains.
9. When maintenance is complete, lower the engine to
reconnect mounts.
PRODUCT STORAGE
Always store the Engine Support Bar in a well-protected
area where it will not be exposed to inclement weather,
corrosive vapors, abrasive dust, fire or any other harmful
elements.
PRODUCT MAINTENANCE
WARNING
:
DO NOT attempt to modify the Engine
Support Bar in any way.
1. Lubrication:
a. J-Hook and Grip Handle – Lubricate the threaded
portion of the J-Hook to ensure smooth rotation.
Added friction may strip the threading over
periods of use which may lead to product failure.
b. Standing Block Connection – Lightly lubricate
the threaded portion of the Standing Block
Connection to allow the Block to slide smoothly
along the Beam.
2. Cleaning: Periodically check the Engine Support
Bar for rust or corrosion. Clean as needed and
wipe with light oil.
DISPOSAL
At the end of the useful life of the OEMTOOLS
™
Engine
Support Bar, dispose of the components in accordance
with all federal, state and local regulations.
