3
Operating Instructions and Parts Manual
24804
4-GALLON MOBILE
PARTS WASHER
08/14
2014 ©OEM-TOOLS
POWER SOURCE CONNECTION
POWER REQUIREMENTS
This product is designed to operate on a properly
grounded 120 volt, 60Hz, single-phase alternating
current (AC) power source fused with a 20 amp time
delayed fuse or circuit breaker. It is recommended that
a qualified electrician verify the ACTUAL VOLTAGE at
the receptacle into which the product will be plugged
and confirm that the receptacle is properly fused and
grounded.
DO NOT OPERATE THIS PRODUCT
if the ACTUAL
power source voltage is less than 105 volts AC
or greater than 132 volts AC. Contact a qualified
electrician if this problem exists. Improper performance
and/or damage to the product will result if operated on
inadequate or excessive power.
CONNECT TO POWER SOURCE
Consult a qualified electrician for proper installation
of receptacle at the power source. This product must
be grounded while in use to protect the operator from
electrical shock. If you are not sure if your outlet is
properly grounded, have it checked by a qualified
electrician. Do not cut off the grounding prong or
alter the plug in any way and do not use any adapters
between the product’s power cord and the power source
receptacle. Make sure the POWER switch is OFF then
connect the power cord to a properly grounded 120V,
60Hz, single phase, 20 amp power source.
EXTENSION CORDS
For optimum performance, an extension cord should
not be used unless absolutely necessary. If necessary,
care must be taken in selecting an extension cord
appropriate for use with your specific product. Select a
properly grounded extension cord that will mate directly
with the power source receptacle and the power
cord without the use of adapters. Make certain that
the extension is properly wired and in good electrical
condition. Extension cords must be a minimum # 12
gauge cord. Do not use an extension cord over 25 ft.
(7.6m) in length.
WHEN INSTALLING YOUR PARTS
WASHER
Check that the Parts Washer power switch is in the
off position, and that the unit is unplugged from the
main power supply.
1. Sit it on a firm, flat, level surface in a well-
ventilated area and away from any open flames.
2. Fill only with a non-flammable water-based
degreaser or cleaning agent, such as Water
Works™ Heavy-Duty Degreaser Concentrate.
(2 – 4 Gallons)
3. Follow the degreaser manufacturer’s instructions
carefully.
4. Do not fill with flammable solvents such as
kerosene, gasoline, etc.
The pump of your Parts Washer may be damaged if
you use aggressive solvents (petroleum, toluene or
thinners etc.) CAUTION! Ensure that you follow any
instructions provided with the product.
WHEN USING YOUR PARTS WASHER
1. Wear suitable protective clothing, gloves and
goggles.
2. Clean off any accidental splashes of degreaser
on skin immediately, following the degreaser
manufacturer’s instructions carefully. Seek medical
attention if necessary.
3. Keep work area tidy and mop up any accidental
spills of degreaser.
WHEN NOT IN USE
1. Switch off pump, close the lid and disconnect from
the electrical supply.
2. Disconnect from the electrical supply before
carrying out any maintenance or cleaning on the
Parts Washer.
ELECTRICAL CONNECTIONS
1. Plug into a standard 120 volt grounded plug.
2. WARNING: This appliance must be grounded.
OPERATION
Always wear protective clothing, gloves and goggles
when using your Parts Washer.
1. Remove plug from bottom of the cleaning tray to
uncover mesh filter. DO NOT operate without mesh
filter in place.
2. Plug the unit into the mains power supply and
switch the unit on. Check that the solvent flows
freely through the outlet hose.
3. Place parts to be cleaned onto the cleaning tray.
Use brush to remove dirt gently from parts to be
cleaned. Ensure any splash back stays inside the
tank.
WARNING
