3
Operating Instructions and Parts Manual
24803
6/18
2018 OEMTOOLS
™
40 GALLON (150L)
PARTS WASHER
POWER SOURCE CONNECTION
POWER REQUIREMENTS
This product is designed to operate on a properly
grounded 120 volt, 60Hz, single-phase alternating current
(AC) power source fused with a 20 amp time delayed
fuse or circuit breaker. It is recommended that a qualified
electrician verify the ACTUAL VOLTAGE at the receptacle
into which the product will be plugged and confirm that
the receptacle is properly fused and grounded.
WARNING
DO NOT OPERATE THIS PRODUCT if the ACTUAL
power source voltage is less than 105 volts AC or greater
than 132 volts AC. Contact a qualified electrician if this
problem exists. Improper performance and/or damage
to the product will result if operated on inadequate or
excessive power.
CONNECT TO POWER SOURCE
WARNING
High voltage danger from power source!
Consult a qualified electrician for proper installation of
receptacle at the power source.
This product must be grounded while in use to protect the
operator from electrical shock. If you are not sure if your
outlet is properly grounded, have it checked by a qualified
electrician. DO NOT cut off the grounding prong or alter
the plug in any way and DO NOT use any adapters
between the product’s power cord and the power source
receptacle. Make sure the POWER switch is OFF then
connect the power cord to a properly grounded 120V,
60Hz, single phase, 20 amp power source.
EXTENSION CORDS
For optimum performance, an extension cord should not
be used unless absolutely necessary. If necessary, care
must be taken in selecting an extension cord appropriate
for use with your specific product. Select a properly
grounded extension cord that will mate directly with the
power source receptacle and the power cord without
the use of adapters. Make certain that the extension is
properly wired and in good electrical condition. Extension
cords must be a minimum #12-gauge cord. DO NOT use
an extension cord over 25 ft. (7.6 m) in length.
ASSEMBLY INSTRUCTIONS
1. Remove machine from carton and inspect for any
visual damage.
2. Remove parts inside the machine.
3. Lay clean and hard cardboard on the floor and lay
machine on its lid. (Make sure you hold cover closed
when laying machine on its lid.)
4. Mount four legs on brackets with M6X12 Phillips head
screws and M6 nuts.
NOTE:
DO NOT TIGHTEN.
5. Place lower shelf between legs with flat surface up and
attach to legs with M6X12 Phillips head screws and
M6 nuts.
6. With legs pressed tight against lower shelf, tighten all
screws to lower shelf.
7. Tighten all the screws installed in Step 4.
8. Stand machine up, being careful to hold lid closed.
9. Put work shelf and basket into the machine.
10. Remove styrofoam packing from pump (see pump label
for instructions) and mount pump assembly into slot on
the side of the machine. Push down firmly on pump so
that it seats itself onto side wall of tub. Place filter screen
in position.
11. Thread the flexible nozzle into the elbow attachment on
pump housing and firmly screw into place.
12. Plug machine into standard 115 volt 60 Hz grounded
outlet and fill with proper amount of fluid.
13. Turn switch on. Fluid should be flowing from the flexible
nozzle.
WHEN INSTALLING YOUR PARTS WASHER
1.
Sit it on a firm, flat, level surface in a well ventilated
area and away from any open flames.
2.
Fill only with a non-flammable water-based degreaser
or cleaning agent to just below the level of the parts
shelf (approximately 24 gallons or 90L).
3.
Follow the degreaser manufacturer’s instructions
carefully.
4.
DO NOT fill with flammable solvents such as
kero¬sene, gasoline, etc.
WHEN USING YOUR PARTS WASHER
1.
Wear suitable protective clothing, gloves and goggles.
2.
Clean off any accidental splashes of degreaser on
skin immediately, following the degreaser
manufacturer’s instructions carefully. Seek
medical attention if
necessary.
3.
Keep work area tidy and mop up any accidental spills
of degreaser.
WHEN NOT IN USE
1. Switch off pump, close the lid and disconnect from the
electrical supply.
2. Disconnect from the electrical supply before carrying
out any maintenance or cleaning on the Parts Washer.
WARNING:
The pump of your Parts Washer may be
damaged if you use solvents like perchloroethylene or
trichloroethylene.