manualshive.com logo in svg

Oemtools 24500, Инструкция по эксплуатации и каталог запасных частей, Страница: 7 / 10

Поделиться
Скачать
Oemtools 24500 Скачать руководство пользователя страница 7

7

Operating Instructions and Parts Manual 

24500

1.8 CFM SINGLE STAGE

VACUUM PUMP

03/14

2014 ©OEM-TOOLS

Initial Preparation

1. Connect vacuum pump to the proper voltage power supply.
2. The vacuum pump is shipped without oil in the reservoir. Remove the exhaust/oil fill 

cap and add oil until it is seen in the middle of the oil sight glass. Re-secure cap.

3. Remove the 1/4" inlet service port cap, turn on the vacuum pump. After 15 seconds, 

replace 1/4 cap back on inlet port.

4. Re-check vacuum pump oil level. Add or remove oil if necessary.
To

 

achieve good final vacuum levels, the oil level should be visually seen through sight

 

glass.

 

CAUTION: DO NOT RUN THIS EQUIPMENT WITH LOW OR NO OIL. RUNNING THIS 
EQUIPMENT WITH NO LUBRICATION WILL CAUSE PREMATURE FAILURE.

VACUUM PUMP IS NOW READY FOR USE.

Vacuum Pump Operation

WARNING: Do not operate on systems under pressure.

Damage to the pump may occur.

1. Check the correct power supply outlet to

 

be used.

2. Connect vacuum pump to the proper 

voltage power supply

3. Check oil level in vacuum pump.
4. Connect vacuum pump as shown in

 

Figure - 1.

5. Open manifold valves.
6. Turn vacuum pump power switch “ON”.
7. Run vacuum pump until final vacuum

 

level is met.

8. Once the final vacuum level is reached, 

close manifold valves, turn power switch

 

“OFF”.

VACUUM OPERATION COMPLETE

Содержание 24500











Отзывы:

Нет отзывов