CONGRATULATIONS ON YOUR PURCHASE OF THE OCL COMPLETE FIXTURE.
OCL lighting provides high quality lighting by integrating experience, creative sensibility and innovation in our products.
By combining pragmatism, perfectionism and high technical standards in the design and lay-out work, we are able to
reach truly unique results.
OCL lighting systems are the new industrial standard in professional high output fixtures. Light quality is a major
focal point in the industry and the OCL X series has been designed to fulfill that specific need. The systems support both
HPS & Metal halide lamps.The OCL double-ended (DE) HPS lamps are proven to be extremely high in Par output, with
a broader spectrum than traditional HPS lamps and only a 5% loss of light at 10.000 hours in operation.
All of our ballasts come standard with PowerControl™, StartSmart™ and dimming feature.
The OCL X series are the next level in professional fixtures, with the ability for central control with the OCL controllers.
With OCL lighting systems “
You are in control of the light
!”
UNIQUE TECHNOLOGY
•
Power Control™: OCL’s Power Control is a software based technology that allows one‐-at-‐a‐-time sequential lamp ignition.
No matter how many OCL ballasts you are running, your lights will ignite one‐-at-‐a‐- time. By utilizing a staggered ignition,
OCL ballasts prevent huge current draws/spikes in your electrical system and is therefore a more efficient means
of lighting your garden.
•
Start Smart™ Technology: When the ballast is powered on, OCL ballasts will send a mV signal through the closed circuit
(between ballast and lamp), to determine a variety of different factors such as: lamp type, open/short circuits, high/low
temps and thermal issues, ignition failure, over flow current, and end of lamp life.
•
World’s Lowest THD%: With an input Total Harmonic Distortion (THD) value of <10% and an output THD% of <12%,
OCL digital ballasts provide the cleanest signal for HID lamps. This provides maximum output, spectral perfection,
and longevity of your equipment.
INSTALLATION
OCL digital ballasts can be positioned universally. The unique design of the heat sink dissipates heat away from the critical
components in the ballast. OCL digital ballasts are designed for use indoors and are sealed against damage by humidity
and dust. When installing your complete fixtures, we recommend to use up to 80% maximum load of your breaker
capacity for electrical safety.
LAMP CONNECTIONS
•
Never turn on the ballast without the lamp cord and lamp installed.
•
Never disconnect the lamp from a live ballast.
•
Hot ‐restrike: it is very important to allow the lamp to cool before attempting to reignite.
Please allow 20‐-30 minutes before restarting to avoid damage to the lamp.
•
Ensure a snug fit when installing lamps.
•
Make sure the mogul socket shows no signs of damage or corrosion.
•
Confirm that power has been disconnected from the ballast before attempting to change lamps.
COMPATIBLE LAMPS
OCL digital ballasts operate both Metal Halide (MH) and High Pressure Sodium (HPS) lamps. While OCL digital ballasts are
compatible with a majority of brand name lamps, OCL digital lamps are recommended. Our technical engineers tune and
match our light systems together for optimal output and spectral balance. Using a matched OCL system has significant
benefits over unmatched systems in terms of light quality and longevity.
•
Please make sure the proper wattage lamp is installed before adjusting ballasts to full power or boost mode.
•
OCL digital ballasts have soft‐start integration, ballasts ease up to full draw.
•
OCL ballasts utilize soft‐ dimming, power will ease up to full draw. It may take a few minutes for the ballast to dim from
each setting. Visible dimming may not be noticeable to the human eye.
MAINTENANCE
OCL digital ballasts are not self-servicable. Disassembling the ballast will void the warranty. The internal componentry
of the ballast is sealed with a resin to protect the electronics. The aluminum exterior of the ballast can be cleaned with a
damp cloth, however make sure the ballast is disconnected before cleaning. Checking all connections regularly to make
sure that no cables have become loose or show signs of damage.
TROUBLESHOOTING
In case the HID lamp will not start, you can try the possible fixes below:
•
Lamp is loose in socket
•
Incorrect voltage
•
Defective or poor wiring
•
Poor electrical connections
•
Incorrect or damaged lamp
POSSIBLE FIXES OR CORRECTIVE MAINTENANCE:
•
Make sure you are using the correct voltage input.
•
Examine wiring to confirm proper connections.
•
Verify that you are using the proper voltage lamp, use OCL digital lamps for best results.
•
Check to make sure there is no lamp damage, sometimes lamps are installed too firmly, look for broken connections.
LEGISLATION
CE LVD approval according to: EN 60598-1:2015,EN 60598-2-1:1989,EN 61347-1:2015,EN 61347-2-12:2005+A1:2010,EN 62493:2015.
CE EMC approval according to: EN 55015:2013+A1:2015,EN 61000-3-2:2014,EN 61000-3-3:2013,EN 61547:2009
WARRANTY
OCL warrants that our complete fixtures are free from manufacturer defects in electronics and mechanical craftsmanship
when used under normal operating conditions for 3 years from manufacture date. If the product shows signs of defect
within this period and which is not due to user error, OCL shall, at its discretion, either replace or repair the product. In case
a replacement is required, a limited warranty will apply to the replacement product for the remaining initial warranty period.
For warranty service, please return the ballast to your retail store together with the original sales receipt.
Accessories included: Power cord, 1 RJ45 interlink cable for plug and play installation, OCL electronic lamp
SPECIFICATIONS
Voltage
Frequency
Current consumption
Rated Power
Power Factor
THD
Input Connection
Operating Temp
Case Temp
Certification
External dim
External dim connector
230V-240V (± 10%)
50-60Hz
2.7A (at 100%)
621W (at 100%)
0,99
<10%
IEC C14
(°C): 0-40 °C
(°C): 70°C
CE
Yes
RJ45 connector built in 2x
230V-240V (± 10%)
50-60Hz
3.4A (at 100%)
785W (at 100%)
0,99
<10%
IEC C14
(°C): 0-40 °C
(°C): 70°C
CE
Yes
RJ45 connector built in 2x
230V-240V (± 10%)
50-60Hz
4.4A (at 100%)
1048W (at 100%)
0,99
<10%
IEC C14
(°C): 0-40 °C
(°C): 70°C
CE
Yes
RJ45 connector built in 2x
600W
750W
1000W