background image

Document UT-MT-0778_EN 

Page 2 of 39 

Edition 11/03/2014 

Supersedes edition 02/03/2014 

LED INSET THRESHOLD/END LIGHT L

THE04

 

INSTRUCTION MANUAL FOR USE, INSTALLATION AND MAINTENANCE 

LIMITED PRODUCT WARRANTY 

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, 
IMPLIED  OR  STATUTORY,  INCLUDING,  BUT  NOT  BY  WAY  OF  LIMITATION,  ANY  WARRANTY  OF 
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. 

OCEM - ENERGY TECHNOLOGY warrants to each original Buyer of Products manufactured by the Company 
that such Products are at the time  of delivery to the Buyer, free of  material and workmanship defects, 
provided that no warranty is made with respect to: 

(a) any Product, which has been repaired or altered in such a way, in Company’s judgement, as to affect
the Product adversely;
(b) any  Product  which  has,  in  Company’s  judgement,  been  subject  to  negligence,  accident  or  improper
storage;
(c) any Product which has not been operated and maintained in accordance with normal practice and in
conformity with recommendations and published specification of Company;
(d) the breaking of the warranty seals, if present, determines the immediate termination of the warranty;
and,

OCEM  -  ENERGY  TECHNOLOGY’s  obligation  under  this  warranty  is  limited  to  use  reasonable  efforts  to 
repair or, at its option, replace, during normal working hours at the facility of the Company, any Product 
which in its judgement proved not to be as warranted within the applicable warranty period. All costs of 
transportation of Products claimed not to be warranted and of those repaired or replaced, to or from the 
facility  of  the  Company  shall  be  borne  by  Purchaser.  Company  may  require  the  return  of  any  Product 
claimed  not  to  be  as  warranted  to  its  facility,  transportation  prepaid  by Purchaser,  to  establish  a  claim 
under  this  warranty.  The  cost  of  labour  for  the  installation  of  a  repaired  or  replaced  Product  shall  be 
borne by Purchaser. Replacement parts provided under the terms of this warranty  are warranted for the 
remainder of the warranty period of the Products upon which they are installed to the same extent as if 
such parts were  original components thereof. Warranty services  provided under  the Agreement  do not 
assure uninterrupted operations of Products; Company does not assume any liability for damages caused 
by any delays involving warranty service. 

IMPORTANT: READ THIS DOCUMENT 

Before proceeding to the operations of installation, commissioning, operation,  maintenance or disposal, 
carefully read the entire document. 

SAFETY INFORMATION 

Extreme caution should be exercised when working with this equipment; it is normally used or connected 
to circuits that operate at dangerous voltages and can be fatal. 
The  following  section  contains  important  safety  information  that  you  must  follow  when  installing  and 
using the apparatus. 
Misuse of the equipment or lack of care in applying safety procedures and prescriptions specified in this 
document, may result in a hazard. 
Avoid contact with voltage or current sources. 
For no reason the protections and the safety devices must be removed. 

Содержание MULTI ELECTRIC LTHE04








































Отзывы: