background image

April ‘13

                  Oceanic Sauna Heater Manual 

Thank you for choosing to buy our Oceanic Sauna heater; please take the time to read 

these  instructions  before  you  begin  as  they  contain  important  information  about  the 

installation and maintenance requirements. 

 

“Oceanic”  sauna  heaters  are  available  in  specifications  from  3kw  to  9kw  and  are 

equipped  with  our  OC-SA  digital  controller.    With  this  not  only  can  you  control  the  temperature  and  time 

duration  of  your  sauna  bath  but  also  the  light  of  the  sauna  room,  alter  the  temperature  display  between 

Centigrade and Fahrenheit; as well as displaying the sauna heater’s status. 

 

Every “Oceanic” sauna heater is thoroughly tested before leaving the factory. 

 

IMPORTANT 

 

Read the manual before installation and operation and then keep it for reference 

 

This equipment must be installed by competent person   

 

This equipment must be connected to an all pole isolator of the correct rating 

 

Disconnect the power supply before exposing electrical connections 

 

All heaters can be connected single phase(230v) or triple phase(400v), this can be easily changed by 

adding bridge connectors across the connections L1, L2 and L3.   

 

5 core silicon bound heat proof cable must be used to wire from the control to the heater. (For 230v and 

400v)    Wire the letters with the corresponding letters on the heater. For example: U V W on the control 

go to U V W on the heater, the three lives for the elements, the reason for having three is because each 

element is controlled individually. When the heater reaches the desired temp it cuts out two elements.   

 

The sauna heater should not be used for any other purpose 

 

Do not cover the heater or allow contact with flammable materials such as toweling – Risk of fire. 

 

Do not operate sauna heater without sauna stone 

 

Do not touch the heater when operational as it is very hot 

 

Sauna heater must have right earth connection, the earth wire should be bigger than the power supply 

wire to sauna heater 

 

The sauna controller should be installed on a dry wall outside the sauna cabin 

Содержание 0CS30



















Отзывы: