Ocean Optics NeoFox Скачать руководство пользователя страница 26

Страница: 26 / 68

3: Using NeoFox with NeoFox Viewer Software

013-20000-009-02-201510

NeoFox Viewer Advanced Settings Window

Note

If the controls on the right side of the screen seem to be disabled, stuck, or if they say

Error

even

after clicking the

Manual Gain

button (

)

, the problem is likely that the firmware and

software versions are not compatible. You will then need to install the appropriate software
version onto your computer to use NeoFox. See

Software Installation

and Appendix B:

Maintenance

for more information.

The Advanced Settings window contains the following tabs (bottom right corner of screen):



Setup



Status



Advanced Status



Advanced Settings

Setup

allows you to perform such functions as Sensor Type Selection, adjusting the APD Voltage (for

firmware versions below 4.00), and Calibrating the Probe.

Содержание NeoFox





































































Результаты поиска

Содержание NeoFox

Отзывы:

Похожие инструкции для NeoFox

Бренды по названию

Популярные бренды

Ocean Optics NeoFox, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NeoFox

Отзывы:

Похожие инструкции для NeoFox

Бренды по названию

Популярные бренды