Oce VarioPrint 6180 Titan Скачать руководство пользователя страница 14

Страница: 14 / 102

Replace the cleaners

Open the doors and covers

Introduction

This procedure is only intended for key operators who received the special maintenance training.

When to do

If the maintenance icon in the dashboard indicates that maintenance is required soon or
immediately.

Before you begin

Make sure that you have 2 new spiral cleaners and 2 new sheet cleaners at hand.

Service key (supplied with the machine)

Socket wrench 10 (supplied with the machine)

Heat-resistant gloves (supplied with the machine)

Adhesive tape (supplied with the machine)

CAUTION

Certain parts of the machine may be hot. Therefore, always use the special heat- and oil-

resistant fuser gloves.

Procedure

Select the maintenance task from the list of the required and suggested maintenance tasks.
[System] view -> maintenance section -> press the [Start maintenance] button.

Press [Start] to start the maintenance wizard.
At the start of the procedure, the machine is turned off.

CAUTION

Wait until the machine is turned off. Opening the doors too soon can possibly cause
injury.

Use socket wrench 10 to loosen the bolt of the front doors (2).

Replace the cleaners

Chapter 2 - Maintenance tasks - Level 1

Océ VarioPrint 6000 line

Содержание VarioPrint 6180 Titan







































































































Результаты поиска

Содержание VarioPrint 6180 Titan

Отзывы:

Похожие инструкции для VarioPrint 6180 Titan

Бренды по названию

Популярные бренды

Oce VarioPrint 6180 Titan, Руководство по обслуживанию

Результаты поиска

Содержание VarioPrint 6180 Titan

Отзывы:

Похожие инструкции для VarioPrint 6180 Titan

Бренды по названию

Популярные бренды