Oce VarioPrint 6000 Plus Line Скачать руководство пользователя страница 69

Страница: 69 / 102

Clean the OPC belt (right)

Procedure

IMPORTANT

Do not touch the OPC belt with your fingers. Wear cleaning gloves.

Rotate the metal OPC pulley until the spots are visible.

[84] Rotate the OPC pulley to locate the spots

Rotate the OPC pulley until the spots are in the indicated area.

NOTE

In this area, the OPC has a hard bottom surface which is required to enable proper
cleaning without damaging the OPC belt.

[85] Position the spots in the indicated area

Apply a small amount of Cleaner J on an offset pad.

Clean any spots with this offset pad.
When you cannot clean the spots with Cleaner J, use Cleaner P.

Clean the OPC belt (right)

Chapter 3 - Maintenance tasks - Level 2

Océ VarioPrint 6000 line

Содержание VarioPrint 6000 Plus Line







































































































Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды

Oce VarioPrint 6000 Plus Line, Руководство по обслуживанию

Результаты поиска

Содержание VarioPrint 6000 Plus Line

Отзывы:

Похожие инструкции для VarioPrint 6000 Plus Line

Бренды по названию

Популярные бренды