5
www.observint.com
© 2019 Observint Technologies. All rights reserved.
Camera
ALI-NS4014R
Target cropping
No
SVC
H.264 and H.265 encoding supported
Day/Night Switch:
Day / Night / Auto / Schedule
Network
Network Storage
Support microSD / SDHC / SDXC card up to 128GB local storage, NAS (NFS, SMB / CIFS), ANR
Alarm Trigger
Motion Detection, video tampering, network disconnected, IP address conflict, Illegal Login,
HDD full, HDD error
Protocols:
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP,
SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour
General Functions
One-key reset, anti-flicker, three streams, heartbeat, mirror, password protection,
privacy mask, watermark, IP address filter
System Compatibility:
ONVIF (Profile S, Profile G), ISAPI
Simultaneous Live
View
Up to 6 channels
User/Host
Up to 32 users
3 levels: Administrator, Operator and User
Client
Alibi Central Management System (ACMS) 3.1 (or newer)
Web Browser
Microsoft® Internet Explorer® (IE) Version 11 (or newer)
Interface
Communication
Interface:
1 RJ45 10M/100M self-adaptive Ethernet port
In-camera storage:
Built-in microSD / SDHC / SDXC slot, up to 128GB
Reset button
Yes
General
Operating Conditions:
-22 °F ~ 140 °F (-30 °C ~ 60 °C),
Humidity 95% or less (non-condensing)
Power Supply
12 Vdc ± 25%, Φ 5.5 mm coaxial plug power
PoE (802.3af, class 3)
Power Consumption:
12 Vdc ± 25%, 0.5 A, max 5.5 W,
PoE (802.3af, 36 ~ 57V, class 3), 0.2 A ~ 0.1 A, max. 7 W
Weather Proof:
IP67
Dimensions:
Camera
: 6.18” × 2.83 × 2.48” (157 × 72 × 63 mm)
Package
: 8.5” × 4.8” × 4.7” (216 × 121 × 118 mm)
Weight:
Camera
: 1.05 lb (467 g)
Package
: 1.40 lb (636 g)
Using the Waterproof Ethernet Fitting
Install the
Waterproof Ethernet Fitting
on the Ethernet cable end at the camera when moisture
or contamination exists in the area near the camera. The fitting includes several parts that must be
installed in a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
If the network cable from the switch or router has a connector
on the end, cut off the connector.
3.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
4.
Place the rubber basket onto the network cable above the lock
nut as shown.
5.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
6.
Install an RJ-45 connector onto the network cable.
7.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
8.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
9.
Push the rubber gasket fully into the end of the network cable
end cap.
10. Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop
cable from
camera
Network cable from
router or switch
Ethernet Fitting installed
Waterproof Ethernet Fitting assembled and connected
Drop cable
end cap
Network drop
cable from
camera
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network
cable
from
router or
switch
Lock nut
