Oakton ION 6 Скачать руководство пользователя страница 21

Instruction Manual 

                                                                                    pH 5/6 & Ion 6 

  

 

19

5.  ELECTRODE CARE AND MAINTENANCE 

For best results, always keep the ISE capped dry and pH/ORP electrode bulb 
wet. Store the pH/ORP glass bulb with pH electrode storage solution. Other pH 
buffers are also suitable. 

NEVER 

use deionised water for storage. Wash the 

probes thoroughly with distilled water after each use. Because your ISE or pH 
electrode is susceptible to contamination or dirt, clean it every 1 to 2 months 
depending on extent and condition of use. 

Clean the pH/ORP electrode using a mild detergent. Wipe the probe with a soft 
tissue paper. Avoid touching the glass membrane with your fingers. Wash 
thoroughly in tap water and then in distilled water. Recalibrate the meter after 
cleaning the electrode. 

6. TROUBLESHOOTING 

Problem Cause 

Solution 

No display 

Batteries not in place. 

a) Insert batteries.  

b) Re-insert batteries in correct polarity. 

“LO” displays 
in the LCD 

Low battery 

Replace batteries with fresh ones. 

Unstable 
reading 

a) Electrode not deep 

enough in sample 

b) Dirty electrode. 

c) Broken electrode 

a)  Place electrode deeper in sample.  

b)  Clean electrode and recalibrate. 

c)  Replace electrode. 

“Er1” display 

Buffer value out of 
tolerance 

Use new pH buffer solution and 
recalibrate. 

“Er2” display 

Single point calibration 

Perform at least 2 point calibration (for Ion 
6). 

“Er3” display 

ISE slope not within the 
specified tolerance 

Check ISE is in good working condition 
(for Ion 6). 

“Er4” display 

Any calibration points 
not within 1 decade 

Ensure any calibration points between 
each other must be within 1 decade (for 
Ion 6).  

Not able to 
calibrate 

a) Display freezes 

b) Faulty electrode  

a) Release reading by pressing HOLD 

key. 

b) Replace electrode. 

Содержание ION 6




























Отзывы: