O.S. engine MaX-37SZ-HRING Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 22

O.S. engine MaX-37SZ-HRING Скачать руководство пользователя страница 7

12

Items necessary for starting

Tools, accessories, etc.The following items are
necessary for operating the engine.

Battery leads

Glowplug battery

The power source for heating the glowplug may be
either a large heavy-duty 1.5volt dry cell, Ni-cd battery
or glowplug Igniter.

1.5 volt dry cell

These are used to conduct current
from  the  battery  to  the  glowplug.
Basically, two leads, with clips,  are
required,  but,  for  greater  conve-
nience,  twin  leads  with  special
glowplug connectors, as shown on
the right, are commercially available.

Battery leads

glowplug Igniter

Make sure glowplug element
glows bright red inside room
or shadow.

Battery leads

In case of 1.5volt dry cell

12V Battery

Starter

Electric starter and starter
battery

An electric starter is recom-
mended for starting.

Hexagon starting shaft

This shaft mounted on an
electric starting motor is driven
into the shaft cup to turn the
engine.

BEFORE STARTING

13

Select, by practical tests, the most suitable fuel from among
the best quality fuels available in your country for helicopter
use. For the best throttle response, a fuel containing 10% to
30%  nitromethane  is  preferable.  Lubricants  may  be  either
castor-oil  or  a  suitable  synthetic  oil  (or  a  blend  of  both)
provided that they are always of top quality. For consistent
performance and long engine life, it is essential to use fuel
containing  AT  LEAST  18%  lubricant  by
volume.  Some  fuels  containing  coloring
additives  tend  to  deterriorate  and  may
adversely  affect  running  qualities.  If  in
doubt compare to a fuel known to be good.

Model engine fuel is poisonous. Do not allow
it to come into contact with the eyes or
mouth. Always store it in a clearly marked
container and out of the reach of children.

Reminder!

Fuel

Model engine fuel is also highly flammable.
Keep it away from open flame, excessive
heat, sources of sparks, or anything else
which might ignite it. Do not smoke, or allow
anyone else to smoke, near to it.

Alternatively, one of the purpose-made
manual or electric fuel pumps may be
used to transfer fuel directly from your
fuel container to the fuel tank.

Manual

Electric

Install a filter to the outlet tube of your
refueling container to prevent entry of
foreign matter into fuel tank. O.S. ‘Super
Filters’ (large and small) are available as
optional extras.

O.S. Super Filter (Fuel Can Filter)

It is recommended to install a good in-
line filter between the fuel tank and
carburetor to prevent entry of foreign
matter from getting into the carburetor.

Fuel Filter

Heatproof silicone tubing of approx.
5mm o.d. and 2.5mm i.d. is required
for the connection between the fuel
tank and engine.

Fuel Pump

Silicone Fuel Line

«
...
5
6
7
8
9
...
»

Содержание MaX-37SZ-HRING























Отзывы:

Нет отзывов