background image

It is of vital importance, before attempting to operate 
your  engine,  to  read  the  general 

'SAFETY 

INSTRUCTIONS  AND  WARNINGS' 

section  on 

pages 2-6 of this booklet and to strictly adhere to the 
advice contained therein.

Also,  please  study  the  entire  contents  of  this 
instruction  manual,  so  as  to  familiarize  yourself 
with the controls and other features of the engine.

Keep these instructions in a safe place so that you 
may readily refer to them whenever necessary.

It  is  suggested  that  any  instructions  supplied  with 
the  aircraft,  radio  control  equipment,  etc.,  are 
accessible for checking at the same time.

Two-Stroke Engine For Airplanes

1

2-6

7-8

9

10

20-21

22

27-30

33

15-17

SAFETY INSTRUCTIONS AND WARNINGS 
ABOUT YOUR O.S. ENGINE

ENGINE CONSTRUCTION,
NOTES WHEN APPLYING AN ELECTTRIC STARTER

ABOUT THE ENGINE

BASIC ENGINE PARTS

BEFORE STARTING

INSTALLATION

INSTALLATION OF THE STANDARD ACCESSORIES

FUEL TANK LOCATION

MIXTURE CONTROLS

GLOWPLUG

STARTING

CONTENTS

RUNNING -IN, IDLING ADJUSTMENT CHART

MIXTURE CONTROL VALVE ADJUSTMENT

REALIGNMENT OF MIXTURE CONTROL VALVE,
SUBSEQUENT STARTINGPROCEDURE

SUBSEQUENT READJUSTMENT,
CARBURETOR CLEANLINESS

TROUBLE SHOOTING WHEN THE 
ENGINE FAILS TO START

CARE AND MAINTENANCE

ENGINE/ CARBURETOR EXPLODED 
VIEWS & PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

MEMO

31

32

34-35

36-37

38-45

11-14

18-19

23

46-47

48-49

24-26

50

Содержание MAX-25AX & MAX-35AX



























Отзывы: