background image

2

!  

!  

Remember  that  your  engine  is  not  a  "toy",  but  a  highly  efficient  internal-
combustion  machine  whose  power  is  capable  of  harming  you,  or  others,  if  it  is 
misused.
As owner, you, alone, are responsible for the safe operation of your engine, so act 
with discretion and care at all times.
If at some future date, your O.S. engine is acquired by another person, we would 
respectfully request that these instructions are also passed on to its new owner.

SAFETY INSTRUCTIONS AND WARNINGS ABOUT YOUR O.S. ENGINE

The  advice  which  follows  applies  basically  to  ALL  MODEL  ENGINES  and  is 
grouped  under  two  headings  according  to  the  degree  of  damage  or  danger 
which might arise through misuse or neglect.

WARNINGS

NOTES

These  cover  events  which 
might  involve  serious  (in 
extreme  circumstances,  even 
fatal) injury.

These  cover  the  many  other 
possibilities,  generally  less  obvious 
sources of danger, but which, under 
certain  circumstances,  may  also 
cause damage or injury.

3

!  

WARNINGS

Model  engine  fuel  is  poi-
sonous. Do not allow it to 
come into contact with the 
eyes or mouth. Always store 
it in a clearly marked con-
tainer and out of the reach 
of children.

Model  engine  fuel  is  also 
highly  flammable.  Keep  it 
away from an open flame, 
excessive heat, sources of 
sparks,  or  anything  else 
which might ignite it. Do not 
smoke or allow anyone else 
to smoke, near to it.

Never operate your engine in an en-
closed  space.  Model  engines,  like 
automobile  engines,  exhaust  deadly 
carbon-monoxide.  Run  your  engine 
only in an open area.

Model  engines  generate 
considerable  heat.  Do  not 
touch  any  part  of  your 
engine until it has cooled. 
Contact  with  the  muffler 
(silencer),  cylinder  head 
or exhaust header pipe, in 
particular,  may  result  in  a 
serious burn.

Содержание MAX-21TM






















Отзывы: