background image

6

NOTES

Adjust the throttle linkage so that the engine 
stops when the throttle stick and trim lever 
on the transmitter are fully retarded. 
Alternatively, the engine may be stopped by 
cutting off the fuel supply. Never try to stop 
the engine physically.

Take care that loose clothing (ties, shirt 
sleeves, scarves, etc.)do not come into 
contact with the propeller.Do not carry loose 
objects (such as pencils, screwdrivers, etc.) 
in a shirt pocket from where they could fall 
through the propeller arc.

Do not start your engine in an area 
containing loose gravel or sand. 
The propeller may throw such material in 
your face and eyes and cause injury.

For their safety, keep all onlookers 
(especially small children) well back (at 
least 20 feet or 6 meters) when preparing 
your model for flight. If you have to carry 
the model to the take-off point with the 
engine running, be especially cautious. 
Keep the propeller pointed away from you 
and walk well clear of spectators.

Warning! Immediately after a glowplug-
ignition engine has been run and is still 
warm, conditions sometimes exist whereby 
it is just possible for the engine to abruptly 
restart if the propeller is casually flipped 
over compression WITHOUT the glowplug 
battery being reconnected. Remember this 
if you wish to avoid the risk of a painfully 
rapped knuckle!

7

NOTES WHEN APPLYING
AN ELECTRIC STARTER

Do not over-prime. This could 
cause a hydraulic lock and damage 
the engine on application of the 
electric starter.

If over-primed, remove glowplug, 
close needle-valve and apply 
starter to pump out surplus fuel. 
Cover the head with a rag to 
prevent pumped out fuel from 
getting into your eyes.

Содержание FS-56A






















Отзывы: