O.S. engine FS-56A Скачать руководство пользователя

Страница: 1 / 21

It is of vital importance, before attempting to operate
your engine, to read the general

'SAFETY

INSTRUCTIONS AND WARNINGS'

section on pages

2-6 of this booklet and to strictly adhere to the advice
contained therein.

●

Also, please study the entire contents of this
instruction manual, so as to familiarize yourself
with the controls and other features of the engine.

Keep these instructions in a safe place so that you
may readily refer to them whenever necessary.

It is suggested that any instructions supplied with
the aircraft, radio control equipment, etc., are
accessible for checking at the same time.

●

2-6

10-13

27-28

34-35

36-37

17-18

SAFETY INSTRUCTIONS AND WARNINGS
ABOUT YOUR O.S. ENGINE

NOTES WHEN APPLYING AN ELECTTRIC STARTER

ABOUT THE ENGINE

ENGINE PARTS NAME

BEFORE STARTING

INSTALLATION

INSTALLING SILENCER

FUEL TANK & LINES

PROPELLER

GLOWPLUG

CONTENTS

MIXTURE CONTROLS

STARTING

RUNNING -IN ("Breaking-in")

IDLE MIXTURE ADJUSTMENT

CARE AND MAINTENANCE

ENGINE EXPLODED VIEW & PARTS LIST

CARBURETOR EXPLODED VIEWS
& PARTS LIST

GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

MEMO

29-30

31-33

14-16

22-23

24-26

Содержание FS-56A






















Результаты поиска

Содержание FS-56A

Отзывы:

Похожие инструкции для FS-56A

Бренды по названию

Популярные бренды

O.S. engine FS-56A, Инструкция пользователя

Результаты поиска

Содержание FS-56A

Отзывы:

Похожие инструкции для FS-56A

Бренды по названию

Популярные бренды