background image

.

MPORTANT:   

If the watch does not run after a new battery is replaced the following initia 

 

 

 

tion has to be done.

After the replacement battery is installed, please follow the procedure listed below:
All hands (hour,minute and second hands) should be aligned to the 12 O’clock position (12:00:00) in order to 
initialize.

1. 

Press and hold S1 (the top button) to set the second-hand to run fast. Wait until all 3 hands go near  

 

11:59 in order to align all 3 hands to 12 O’clock.  

2. 

Push the S1 (the top button) once to Stop fast running.

3. 

Continue to press S1 one press a time until all hands align at 12:00:00

**If you accidentally go past the 12, start this process again.
4. 

When all hands are aligned at the 12 0’clock position (12:00:00), PUSH S2 for 1 second to confirm.

DO NOT push any button after the second hand has stopped.  Wait until your watch runs again.

5.  After confirmation, you need to do the following when the watch resumes running:

● Check and set your watch to the right Time Zone (go to “Time Zone setting” for details)
● Place the watch near a window location where reception is possible for 24 to 48 hours to allow the watch to 
receive the radio signal and  to set the correct time.  The watch will automatically initiate a reception at 3AM 
after receiving a valid time signal, and the hands move on to the correct time.

Thank you for buying this product. If you have any question, please call to our Tech Support Department at 
1-800-399-1629 or visit our website at www.newyorkstandardwatch.com

New York Standard Watch Company 

.

 www.NewYorkStandardWatch.com

Page 9

M43 multi-band version (1.0)

NYSW

Instruction Manual

Fifth Avenue Series - 1310L-021GN

(3 hands Analog-Digital Atomic Watch)

Содержание FIFTH AVENUE SERIES










Отзывы: